NAV5800AWW Amana Washer - Instructions

had to completely disasemble whole washer drum and mechanical components to remove upper bearing on transmission,the drum hub was corroded on the shaft. I had to use a gear puller and a propane torch to get the hub off upper shaft of the transmission. then press the bearings in the respective sheet metal supports. reassembly was alot easier than taking it apart. Not a job for an average homeowner. It would not have been repaired without the wheel puller. all the seals were reusable A week and a half of use later no leaks and works great

I had no problem replacing the triple lip seal and bearing. I cracked the plastic tub, which after 10 years was very britle and cracked in two places ON THE SIDE. To remove the bearing I had to improvise a bearing removal tool using a puller I had on hand and a 1 lb metal coffee can. It worked great! You need to use some type of pulling device to remove the bearing without damaging the tub.

Followed video on PartsSelect website, they made it real easy.

Hardest thing was moving washing machine away from wall. Two screws on panel. One screw for hose.

Removed and replaced mixing valve. Shut off hot & cold water supply to machine. Pull machine electric plug. Access back of machine. Remove water supply to machine. (Pliers) Be sure to keep some paper towels handy to pick up residual water. Remove screw that holds mixing valve mounting plate to machine. Pull plate away from machine. Undo hot and cold elect. connectors to valve. Remove water supply to valve. (Black hose-screwdriver.) Remove screw holding valve to mount plate. (Nut driver.) Install new valve onto mount plate. Reverse process used to remove valve. Test by turning on machine.

After receiving the new hose we replaced the hose and tested the washer by running a rinse cycle. The new hose fixed the problem.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Removed spring, then hoses and then belts. When all was removed we loosen the old washer pump and installed the new pump. Everything was re-installed and was put to wash. At first it leaked water that was already sitting there, but then it work like new. Oh I also read the instruction on this website, I recommend the site to everyone!!

Replaced the mixing value using the kit purchased from PartSelect. The instructions with the kit plus the installation tips found on their WEB Page were extremely helpful. Everything went as predicted except I had to cut and insert a new piece of wire on the white wire between the hot and cold electrical connections. I used two crimp connectors to lengthen the wire. This was a very simple job for a 73 year old man like me. Thank you for the tips and quick delivery of the mixer value kit.

Removed old hose by sqeezing clamps and sliding off of fittings. Placed clamps on new hose. Slid hose on fittings. Repositioned clamps over end of hose. Job done.

removed both hot and cold fill lines and front of washer panel. removed screw holding mix valve plate t the back of the washer . Unpluged connections to mix valve and replaced valve. ( note removing the top of the washer is needed and can only be done by first removing the front by sliding a thin screw driver between the top and front panel to release the clips at the ends.)

After totally disassembling the washer ; the parts arrived, wrong parts! called and resolved issue, recvd parts and proceeded without special tools, PB Blaster solvent is awesome!!! I removed the seal & bearing with little effort with a hammer and screw driver. Greased new seal and installed effortless. Waher back in operation in less than 2 hours of receiving the parts.

I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.

First, I removed the screws, then removed the pump. I, then, installed a new pump.

disconnected valve replaced with new, real easy. I removed motor and belt ,4 bolts, than removed 3 star screws from pump, replaced pump and replaced unit. Worked great!!!
Delivery of parts was faster than promised, standard shipping.