MZD2752GRW Maytag Refrigerator - Instructions

Several days back I found I couldn't get any ice from the ice maker. I was able to hear noise from the ice maker but no ice would dispense. I opened the freezer and removed the ice bucket to find out that the Auger has broken off from it's plastic housing in the back of the freezer. I went to partselect.com to find the part(s) that were broken, it was much easier because of the diagram/images they have for each individual section of the fridge. Parts came quickly and as expected.

The replacement of the auger motor is very easy if you follow these steps:

1 - Remove the ice bucket from the freezer
2 - Unscrew the one screw on the bottom left side of the ice bucket tray (the tray holds the ice bucket in place). I used a small needle nose plier to remove this screw as I was having a hard time with my drill or wrench set. After you've removed the one small screw, lift the tray up and slowly pull towards you.
4 - You'll quickly see that the auger motor and magnetically controlled yoke are connected with a wire harness to the back of the freezer.
5 - Gently crimp the ends of the wiring harness connector with your hand and slowly pry away from the freezer. Once you've removed the wiring harness you can remove the entire tray with the parts attached (yoke/auger)
6 - Unscrew the auger motor from the tray. You'll also have to remove the auger from the motor else it won't come out. In my case the whole plastic attachment was broken so I didn't have to do this (ie I replaced the ice tray as well). It was impossible for me to remove the auger from the auger motor, not sure why the auger was so tightly attached to the motor - it could be the reason the auger motor broke from the ice tray?, so I had to buy a brand new auger motor and auger (ie Auger Drive Motor Kit). I hope you have more luck then I did removing the auger. If you can't remove it you'll need to buy the Drive Motor Kit (which comes with the drive motor, detached auger and auger washer).
7 - Once/if you've removed the auger from the motor and remove the motor from the ice tray, you can proceed with the replacement of motor.
8 - Using needle nose pliers remove the three power connections on the motor (white/neutral?, pink/power?, green/ground, note where the connections were when you removed them because you'll replace them in the same place on the new motor).
9 - Attach new motor to ice tray with the four screws, attach the auger and auger washer to the auger motor, attach the power connections back (white, pink, green).
10 - Re-connect the wire harness to the back of the freezer
11 - Move ice tray back into place, and attach the one screw back to the ice tray to hold it in place.
12 - Replace the ice bucket back onto the ice tray
13 - Done, you should now get ice!

Good luck, I hope this helps. It's easy and you don't have to pay three times this price to replace these ice bucket parts.

First let me start out by saying Parts Select was by far the best pricing and had SUPER FAST SHIPPING! Literally had the product within 2 days (regular shipping). Matter-of-fact only needed the round white piece for the ice maker door and they sold just the piece without having to buy the kit. Everyone else even Maytag would only sell me the whole kit. Anyway...as if you couldn't tell I am a woman (28) who fixes nothing. Would much rather pay someone to do it : ) However I took it upon myself to try and fix this after bugging my husband for a year. Needless to say I Did it and it took maybe 5 minutes. You do need a torch screwdriver (star shape) and yes it was in my purple girlie tool bag! Just a matter of taking out 5 screws taking the old door/flap off and replacing it! Take the time to clean while everything is already apart too. Very easy , if I can do it anyone can!

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

I noticed that the thin plastic flap was missing. I squeezed the housing, unsnapped and pulled. INstalling the new part was just the reverse. No more frozen vegetables.

Ice door flap was broken and warm air was getting into the freezer. I removed a total of 4 screws to get to the flap. Total time was less than 15 minutes and very easy. Partselect customer service was very helpful and friendly. If you have any questions, do not hesitate to call them. They were very helpful! I have this site bookmarked!

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

From the beginning I have never had good water flow in the door and ice cubes turned out funky. I tried replacing the filter once with hardly noticeable change. The change I did see was $35 less in my pocket. So I bought a filter bypass plug and it now works like a champ. I have well water so I trust its quality and I am very satisfied. I would describe how I did the repair but if you don't no how to change out the filter you probably shouldn't be trying it.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

Simple to fix. Watched the video and noted what to do.
Replaced the control board, solenoid, and limit switch. Woks like new!

My ice maker was overflowing and i realized that it was the water valve that needed replaced. unscrewed 1 nut, unhooked 3 water lines, unhooked electrical components and re-installed in reverse order. took about 10-15 mins.

first i remove the two screws like the guy said on your web site. then i pulled the cover off with a upward motion revealing three more screws witch i removed. I then removed the dispencer. unpluged the wires and removed the switch and pad and replaced with new parts.I reinstalled the wires then the unit, installed the screws and cover.Checked for proper operation.Then enjoyed that cold beer! Thanks to your wed site and repair info. I saved at least 100 buck to the repair man. Thanks Partselect.com

Easy to diagnose problem because there was water to the water dispenser but none to the newly installed icemaker. Originally did attempt to clean the solenoid but found the plunger assembly damaged.

New part arrived sooner than I thought it would. Takes about as much time to remove the lower vent cover as to replace the valve. Remove the electrical plug from the wall, valve off the main water supply, remove lower vent cover, disconnect the supply hose from refrigerator valve assembly, remove one hex head mounting screw and you have both water valves in your hands. Identify the valve the supplies water to the filter and the one that supplies water to the icemaker/water dispenser. Then confirm which plastic water supply line goes to the water dispenser and which goes to the icemaker. Hose diameters are different but it is good to know. Disconnect the plastic water supply lines from both the ice dispenser and the icemaker portions of the valve. Replacement solenoid valve does not have thread on type compression fittings. Snip about an inch off of each hose and then press into the appropriate valve orifice.

Making sure the plastic supply lines do not get crimped, remount the valve assembly, reattach the supply hose, valve on the water and check for leaks. No leaks, reinstall dust cover and plug the refrigerator back in.

Move the unit back in place and then take a long deserved beer out and have a celebratory toast for a job well done.

took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks

I had to cut off the old yoke since the threads had stripped and it would not come off. Once I did that all I had to do was to remove 4 screws on the auger motor and replace it with the new auger motor. Then I put the yoke on the new auger motor shaft and then put the unit back in the freezer. Work time was less than 15 minutes with no problems.