MV1604ST01 LG Microwave - Instructions

All Instructions for the MV1604ST01
16 - 30 of 47

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The old ones broken
5 of 7 people found this instruction helpful.
  • DIANE from PORT ORANGE, FL
  • Really Easy
  • 30 - 60 mins
Took old ones out, threw away and put new ones in easily.
Was this helpful?
Thank you for voting!
When the MW door was opened a fan would start running. Close the door the fan would go off.
4 of 6 people found this instruction helpful.
  • vic from Allen, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed the MW from the wall. Took the top screws off the air vent. Then removed the two screws holding on the display. I then moved the display to its side and it revealed the micro switches. I removed the plug in leads from the micro switch one at a time. I did this with all three micro switches only one at a time. I reinstalled everyth ing and plugged it in. No more fans starting when the door is opened.
Was this helpful?
Thank you for voting!
food does not get hot, carousel did not turn, all other indicators worked
3 of 3 people found this instruction helpful.
  • John from SEVERN, MD
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Read the troubleshooting section on this site. Figured it was an interlock problem because the food was not getting hot (magentron not turning on) and the carousel was not turning. Did not think both the carousel motor and magnetron failed at same time, thus indicated an interlock problem. The interlock switches are actuated by the door latch. Replaced the assembly locker piece with all three switches (only a $20 dollar part) and microwave was fully operational again. Wife and kids think I am a hero.
Was this helpful?
Thank you for voting!
UNABLE TO INSTALL DUE TO DAMAGED IN SHIPPING
3 of 4 people found this instruction helpful.
  • Tina from EL DORADO, KS
  • Very Difficult
  • More than 2 hours
WORTHLESS...I EMAILED YOU ON 2/7/22 AFTER RECEIVING THE DAMAGED FILTER DUE TO NOT SHIPPING IN A HARD OR SOMETHING IN THE ENVELOPE TO PROTECT THE FILTER FROM BEING BENT.
I HAVE NOT HAD ANY RESPONSE FROM YOU FOR THE DAMAGED FILTER OR WHEN I CAN EXPECT ONE THAT I CAN USE.
UNSATISIFACTORY SERVICE!
Was this helpful?
Thank you for voting!
Door switch was burnt out
5 of 10 people found this instruction helpful.
  • Edward from ORCHARD PARK, NY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Removed outer cover

removed lower door switch

installed new switch

Wa La!
Was this helpful?
Thank you for voting!
Items were not getting heated up in the microwave,
2 of 2 people found this instruction helpful.
  • Kenneth from CRYSTAL LAKE, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I went to LG website enter model number and was given a list of parts that need to be replaced with a percentage of which part fails the most. I order micro switch PS3522738 which arrived and PS3529293 was backordered. I installed the one that arrived. The microwave worked briefly. I reordered and waited for both switches to arrive and in stalled both. The microwave still doesn't work.
Was this helpful?
Thank you for voting!
Oven would not start when closing door.
4 of 8 people found this instruction helpful.
  • Raymond from DEPEW, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
Removed some cosmetic panels. Removed the assembly with micro switches. Examined the faulty switch by checking the clicking action of switch. Two others were ok by this method. Replaced the switch with new one. Works fine so far. Thanks to web site and YouTube videos.
Was this helpful?
Thank you for voting!
Door switch malfunction
2 of 3 people found this instruction helpful.
  • Sherry from PINELAND, SC
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Take cover off microwave. Check door switches to determine which one was faulty.Remove and replace faulty switch.
Was this helpful?
Thank you for voting!
Replacing top vent filter
2 of 3 people found this instruction helpful.
  • Paul from CHARLOTTESVLE, VA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Followed owners manual instructions to the letter: removed two top screws, opened the unit door so I could slide out the old filter. We don’t cook much at all in the unit, mostly just heating coffee and reheating leftovers. BUT! The top grill was pretty greasy and needed hot soapy water to clean, including in the depths of the top area. T he whole process, especially the company website for part ID and purchase, was slick!
Was this helpful?
Thank you for voting!
did not include screw to secure it to celing of the microwave rempved
2 of 3 people found this instruction helpful.
  • Bill from TAMARAC, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
removed old cover put the new one in place found right size screw from my tool box, tightened it.
Was this helpful?
Thank you for voting!
Microwave fan would come on when door open. Timer and unit would not switch on.
1 person found this instruction helpful.
  • Dick from SANDY, UT
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I looked up my problem on the internet and found a very helpful video. Microwave on video was different brand but the internals and methods were very much the same. The video made it simple and easy to fix. Found the replacement switch on the LG parts site and ordered. Two different switch types. One with red switch, the other green. Part was $7.28. Saved a bundle in service costs. Here is the repair video.

https://www.youtube.com/watch?reload=9&v=_AglBJoHgDs
Was this helpful?
Thank you for voting!
Used You Tube and things went smoothly
1 person found this instruction helpful.
  • John from SARASOTA, FL
  • Really Easy
  • 30 - 60 mins
Removed burned pieces and reinstalled new.
Was this helpful?
Thank you for voting!
The new part was too thick for the worn out plastic ring which is obsolete.
1 person found this instruction helpful.
  • James from PURCELLVILLE, VA
  • A Bit Difficult
  • 30 - 60 mins
Needed to raise the part to match the ring. I used peanut butter to hold plastic shim while replacing to hold it in place. Built in Oct. 2009.
Was this helpful?
Thank you for voting!
suddenly stopped working while in use
2 of 4 people found this instruction helpful.
  • Kevin from Colonia, NJ
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
i unplugged the unit,unscrewed the outer shell so that all the wiring and internal components were visible.starting at the first of three micro switches i removed the slip on terminals installed the alligator clips too the wires so the switch would now be bypassed.i made sure the wires and clips were not touching anything plugged unit in and it worked.i then installed the new switch and closed up the outer shell
Was this helpful?
Thank you for voting!
Leek
1 person found this instruction helpful.
  • Krzysztof from NEW BRITAIN, CT
  • Easy
  • 30 - 60 mins
Change gasket
Was this helpful?
Thank you for voting!
All Instructions for the MV1604ST01
16 - 30 of 47