MSS25N4MKZ01 Maytag Refrigerator - Instructions

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

My husband tackled the job....but before this repair he had to replace ours at home so he had some experience at it....although...on this fridge he had to hook up the water line and all...but basically was not too hard...and the ordering of the part and delivery was excellent...

On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

I got the part....I put it in. That's about it.

googled the model of ice maker and refrigerator, ordered replacement ice maker from Part Select. Received next day, installed it in 10 minutes and it worked like a charm.

I removed a few items from the freezer to make room. Husband took out the old ice maker. (We were sure it would require moving the refrigerator out which would have been a huge undertaking given the tight fit) To start he simply replaced the ice maker with the new one. I started watching...and even though it says that it will take up to 24 hours to make ice, it began making ice probably within an hour! After about 6 batches, I threw those out. (just in case there was anything in the line that would contaminate the cubes)It is obvious that the old one had not worked properly for a long time! The ice container is full to almost over-flowing! It has not been this full in a very long time, as I use ice every day! Simple fix! And might I add...LIGHTNING FAST DELIVERY!! It was here in two days! We are thrilled!!!!!

I watched your repair video, read the instruction enclosed with the icemaker and made the repair in about 15-20 minutes. There is an issue that others need to be aware of once the water pump is repaced and the tubing is connected and the icemaker is installed and turned back on; it take 20-30 minutes to pump the air out of the line and the for the water to actually fill the the fill tray (you made the install correctly, the delay in filling is not covered by either the video or the book just be patience don't disconnect and reconnect anything it will eventually fill and make ice and less than 48 hours). This vendor offers 4 star customer service at a fair and resonable price (I priced the parts separately prior to purchase and the kit is the way to go). I received the product within 3 days, shipped groung delivery. I would use your products and online service advice for installation on other appliances in the future if needed. You have earned my trust, and repeat business in the future; and I will gladly recommend you to others. Your customer focus and service is second to none. I am a fully satisfied customer!!sincerely, a. Walker

Unplugged refrigerator. Unplugged ice maker and took out three screws holding ice maker. Put new ice maker and attached three screws. Plugged ice maker in. Plugged refrigerator in and ice maker began working. Threw out first ice cubes made. Unit now working fine.

remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed approx 3/4" under edge of refrigerator.

Viewed the viedo - it showed what to do

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

unsnap old part and gently push new shelf bracket in till it snaps into place.

Removed/replaced ice maker and valve per enclosed instructions. If you can service your own lawn mower this R&R should be easy for you.