MSD2722GRQ Maytag Refrigerator - Instructions

Confirmed the condenser fan was the problem when I noted it was not running when the compressor was on. Removed 3 mounting screws, unpluggede the fan. Removed and replaced the mounted flange(3 screws) and remounted. Plugged in fan and it started running.

Thanks for the diagrams and quick delivery. This is the second repair on appliances I have made with your parts and probably saved $300-400 in service calls.

First I removed the spill tray, and removed the two screws on the bottom of the dispenser. I was then able to remove the front of the dispenser, which revealed 3 more screws. After removing those screws, the entire assembly lifts out. I removed the old pad, put the replacement pad on, replaced all the screws and the tray, and was done! It took about 10 minutes, start to finish. I saved at least $75 on the repair by doing it myself, and the part only took 3 days to arrive. Best of all, the water and ice dispenser works like new! Thanks, PartSelect!

Removed the ice bucket from the freezer. Removed the single screw on the left side with a nut driver, then lift and pull the tray toward you...there is a wiring harness in back of the tray that I had to unplug...easy, pinch the sides of the plastic connector and it disconnects..and the tray came out of the refrigerator...and the cussing started. Since the threaded yoke was stripped it could not be unscrewed from the motor shaft...I took my trusty Dremel Tool and cut the shaft off so the yoke could be separated from the motor shaft and the motor could be removed from the plastic housing. From here on it was a piece of cake...install the new motor and screw the new yoke onto the motor shaft... I think it has a left handed thread, like the old propane bottles used to have..slide the tray back in, reconnect the wiring harness (it only plugs in one way), make sure the tray is sitting on the 4 side supports, put the single screw on the left side and you are done....put the ice bucket back in and flip the bail down and you should be back on business....!!

I Removed the two wires from the old relay. I Then pulled the old relay off the compressor. Next, I had to get the overload seperated from the old burnt relay, which took some care not to break. The old relay and overload is in a plastic compartment. Then I followed the directions that came with the new relay. The only confusion came with getting the two wires back onto the terminals of the new relay, mainly because the old relay was burnt so badly I didn't have any idea how it was originally wired. I crossed the two wires on the terminals of the relay. The compressor would click off and on, but would not start blowing cold air. I swapped the wires on the terminals and it started working immediately.

I don't know anything about repairing a refrigerator - I'm a computer tech. I noticed that the outside of the fridge was warm to the touch and the inside was not getting as cold as it should. I took the lower back panel behind the fridge off and noticed that the fan was not spinning. The local parts dealers did not have the condenser fan motor that was needed but they did say that they do go bad. I decided to order one from PartSelect.com and do it myself. Using a 1/4 inch nut driver and a flat head screw driver to pry the old motor out of the casing, I got the job done in about an hour or so. It's a relativly easy job. Besides the ouside panel screws, there's 3 screws on the inside near the fan blades you have to reach in to get. Pop out the whole assembly, unscrew the nut that holds the blades on and pry out the old motor and replace.. Try it yourself and save a couple hundred bucks!

Just pulled out ice bucket put to the side and then pulled out framed housing that surrounds the ice bucket tray and put on table
went in the rear where the turn motor is and disconnected the wires from the housing next to it and disconnected the motor which had cracked the wal it was mounted to and broke and fell which left a huge hole and the , took the 4 screws out and remounted it onto the new housing rear wall, note that to get the twist key lever that unscrews clock wise you may have to hit wit a hammer bluntly to brak it lose first then it unscrews easy, but this has to be done first before re assembly of the motor as it goes through the new housing wall , once this is donr then put your screw end through the hole and re assemble the wing devise back onto the moter screw drive which it will screw on counter clockwise and tap a few quick times to snug with a ball hamer or a small hammer, T
The hinge door pin is real easy, just unscrew the top of door 3 screwa and lift off the door set aside put new door pin hinge on then set the door back onto the pin hole align up and set it back down in the hinge hole and replace screws on the upper door hinge on top of fridge. all this took about 5 minutes tops, it took me more time to take all the items out of the doorway of my fridge that it did to do the task itself. Hope this could help.

Step 1 :I had to remove the ice drip tray just pull it out.
Step 2 remove the 4 or 5 screws holidung in the control module (push button display pad)
step 3: pull the plug from the diaplay panel
Step 4: remove broken door from slot and slide new one in. Be carfull not to let the brass plug fall out of it does it just slides back in.
Reverse all steps your done about 20- minutes..I am a building engineer by trade. I think the average person 30 to 60 minutes..

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

followed the instructions provided and that's it!

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed

1. Turn off fridge and Pull plug from wall.
1a. Turn OFF water supply!
2. Remove rear dust cover to gain access to water valve.
3. Mark power connectors(red/green) attached to water valve before removing them. Remove connectors.
4. Remove supply line from old valve.
5. loosen mounting screw holding old valve in place.
6. remove valve.
7. disconnect two plastic water lines from valve.
8. Cut 1/2 inch off the end of each plastic line to get to un-streached line. Make sure you have enough line to still reach valve!
9. Insert plastic lines FIRMLY into outlets of NEW VALVE to lock in place. outlets are different sizes so you can't reverse them!
10. Install new valve and tighten mounting screw.
11. replace/tighten supply line to new valve.
13. Replace dust cover!
14. Plug in, Turn on fridge.
15. Turn on water supply, bleed air out by drawing a glass of water at door, and check for leaks!
All Done!

Overall, replacing the ice maker wasn't too bad but it wasn't nearly as easy for me as it seems to have been for some. In my case, the fridge was an Amana and the ice maker was mounted in such a way that disconnecting the power connector was difficult. The ice maker had to be completely dismounted before any access to the power connector was even possible. The short power cables made it very difficult to get the ice maker into a position where I had a good view of the power connector enabling me to see how to release it. The only other challenge was the cup that the water line goes into. The replacement ice maker did not come with the right cup - the instructions said to replace the provided one with the old one. No instructions for this procedure were provided and it looked to me like it might involve significant disassembly, something I wanted to avoid for fear of breaking a plastic part on the new ice maker (something I had already done when disassembling the old ice maker). So instead of replacing the cup, I modified the new one to match the old one. This involved removing a cutout on one side and covering a hole on the other. Installation of the new ice maker went fine and the water leak problem was fixed.

R & R Icemaker Assembly. Took out 3 screws and unpluged Icemaker & replaced with new part. very easy and the service from PartSelect was fantastic.
Very Satisfied,
Ron Martin

Replaced the water valve with the new part by removing 2 screws to allow folding back of the cover, removing 1 screw and pulling valve assembly out. 1 more screw took the two valves apart, unscrewed the water lines, replaced them on new valve (with newer push-in connections it was even easier), reassembled unit, turned the water on, checked for leaks, none found. Works great, was very easy.

removed the ice chute door, unhooked the computer board replaced the flap. The only problem was the spring loaded part of the ice chute door come up and the little plunger came loose. It only took a few minutes to replace the plunger back in the holder and replaced the ice chute door. The best part of the whole job was that I ordered the part on Monday afternoon and the part was at my door Wednesday. The Parts did an excellent job of getting the part to me quickly.