MSD2422GRQ Maytag Refrigerator - Instructions

After moving the refrigerator away from the wall I removed the cover on the lower back of the unit by removing the screws that held it in place. The condenser fan was not turning and there was heat build up in the area causing the refrigerator to not work properly creating elevated temperatures in both the freezer and regrigerator. Removal of three torx screws from the original motor was all it took to get the motor free. By turining it and working the fan blade around the mounting bracket I had the motor out in just a few minutes. Replacing the new motor was just as easy to reinstall. The fan was removed from the old motor and placed on the new for installation. The original motor was wired to accept a connector from the wiring harness of the refrigerator. I simply cut the connector off the wiring harness and stripped the insulation from the wires which easily allowed me to connet the wires of the motor and harness with two wire nuts. Three self tapping screws were used to hold the motor in place replacing the torx screws. Installed I plugged the unit in and immediately the fan started spinning as the unit came to life. Cleaned and replaced the cover over the back and slid back into its spot. Running as good as it did when it was new. Easy job to take care of.

Philips head screwdriver and ten minutes was all it took! I removed the two screws that hold the icemaker assembly in place, then pulled it out a little and disconnected the electrical plug freeing the icemaker assembly. Then I snapped the external parts off my old icemaker assembly and snapped them on the new icemaker assembly. Installing the new icemaker assembly was just as fast and easy. I snapped the electrical plug into the new icemaker assembly, then screwed in the two screws. It was making ice shortly thereafter. Glob free ice! I'm glad I didn't call a repairman. I probably saved a hundred bucks. A ten year old could accomplish this simple and easy task. No wonder the Maytag repairman has time on his hands.

Several days back I found I couldn't get any ice from the ice maker. I was able to hear noise from the ice maker but no ice would dispense. I opened the freezer and removed the ice bucket to find out that the Auger has broken off from it's plastic housing in the back of the freezer. I went to partselect.com to find the part(s) that were broken, it was much easier because of the diagram/images they have for each individual section of the fridge. Parts came quickly and as expected.

The replacement of the auger motor is very easy if you follow these steps:

1 - Remove the ice bucket from the freezer
2 - Unscrew the one screw on the bottom left side of the ice bucket tray (the tray holds the ice bucket in place). I used a small needle nose plier to remove this screw as I was having a hard time with my drill or wrench set. After you've removed the one small screw, lift the tray up and slowly pull towards you.
4 - You'll quickly see that the auger motor and magnetically controlled yoke are connected with a wire harness to the back of the freezer.
5 - Gently crimp the ends of the wiring harness connector with your hand and slowly pry away from the freezer. Once you've removed the wiring harness you can remove the entire tray with the parts attached (yoke/auger)
6 - Unscrew the auger motor from the tray. You'll also have to remove the auger from the motor else it won't come out. In my case the whole plastic attachment was broken so I didn't have to do this (ie I replaced the ice tray as well). It was impossible for me to remove the auger from the auger motor, not sure why the auger was so tightly attached to the motor - it could be the reason the auger motor broke from the ice tray?, so I had to buy a brand new auger motor and auger (ie Auger Drive Motor Kit). I hope you have more luck then I did removing the auger. If you can't remove it you'll need to buy the Drive Motor Kit (which comes with the drive motor, detached auger and auger washer).
7 - Once/if you've removed the auger from the motor and remove the motor from the ice tray, you can proceed with the replacement of motor.
8 - Using needle nose pliers remove the three power connections on the motor (white/neutral?, pink/power?, green/ground, note where the connections were when you removed them because you'll replace them in the same place on the new motor).
9 - Attach new motor to ice tray with the four screws, attach the auger and auger washer to the auger motor, attach the power connections back (white, pink, green).
10 - Re-connect the wire harness to the back of the freezer
11 - Move ice tray back into place, and attach the one screw back to the ice tray to hold it in place.
12 - Replace the ice bucket back onto the ice tray
13 - Done, you should now get ice!

Good luck, I hope this helps. It's easy and you don't have to pay three times this price to replace these ice bucket parts.

First let me start out by saying Parts Select was by far the best pricing and had SUPER FAST SHIPPING! Literally had the product within 2 days (regular shipping). Matter-of-fact only needed the round white piece for the ice maker door and they sold just the piece without having to buy the kit. Everyone else even Maytag would only sell me the whole kit. Anyway...as if you couldn't tell I am a woman (28) who fixes nothing. Would much rather pay someone to do it : ) However I took it upon myself to try and fix this after bugging my husband for a year. Needless to say I Did it and it took maybe 5 minutes. You do need a torch screwdriver (star shape) and yes it was in my purple girlie tool bag! Just a matter of taking out 5 screws taking the old door/flap off and replacing it! Take the time to clean while everything is already apart too. Very easy , if I can do it anyone can!

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

Removed housing on the freezer side and removed the assembly by removing the two bottom clips and then unclipping the wire harness, two prong, and replaced as remvoved. Power was off of course. Watched for 24 hours and recovered housing and its been working great.

I noticed that the thin plastic flap was missing. I squeezed the housing, unsnapped and pulled. INstalling the new part was just the reverse. No more frozen vegetables.

Ice door flap was broken and warm air was getting into the freezer. I removed a total of 4 screws to get to the flap. Total time was less than 15 minutes and very easy. Partselect customer service was very helpful and friendly. If you have any questions, do not hesitate to call them. They were very helpful! I have this site bookmarked!

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.

From the beginning I have never had good water flow in the door and ice cubes turned out funky. I tried replacing the filter once with hardly noticeable change. The change I did see was $35 less in my pocket. So I bought a filter bypass plug and it now works like a champ. I have well water so I trust its quality and I am very satisfied. I would describe how I did the repair but if you don't no how to change out the filter you probably shouldn't be trying it.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

First I unplugged the refrigerator, then next I removed the (4) screws holding in the inside back panel section of the freezer covering the cooling coils, the fan motor is attached to the removable panel.
I then unplugged the wiring harness to the fan motor which allows you to completely remove the freezer inside panel in order to replace the fan motor on a counter top or benchtop.
I removed the (3) spade terminal wiring from the fan motor and the nuts holding the motor on the frame. I then replaced the fan motor and blade the same way I had removed the old one, and then reattached the wiring terminals on the same terminals as the existing motor, making sure that black, red, and green do not get mixed up. I placed the rear panel back inside freezer and plugged in the wiring harness, fit panel back to original position and reinstalled the (4) panel screws. I once again plugged in the refrigerator and restored power. Everything is working fine.

Read wiring diagram found what would stop power to compressor. Removed thermostat checked for continuity which there was none no matter what position dial was in. Checked operation of remaining components in the refrigerator by jumping the two wires together that are connected to the thermostat, plugged refrigerator back in and compressor kicked right on.