- Home
- MMV6180WS1
- Instructions
MMV6180WS1 Maytag Microwave - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!
4 of 18 people
found this instruction helpful.
-
Stephen from SPRINGFIELD, WV
- Very Difficult
- 1- 2 hours
-
Pliers, Screw drivers
Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!
Was this helpful?
Thank you for voting!
replace filter
-
Robert from Southfield, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers
Time to replace the charcoal filter
Was this helpful?
Thank you for voting!
Noisy turntable motor
-
Bruce from Rock Island, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unplug microwave. Remove turntable and support from inside. Remove outside bottom cover (10 screws). Remove 2 torx screws holding motor in place. Remove 2 wires from motor, noting colors. Wires are held with spade connectors that has a small tab that needs to be depressed. Remove washer from motor and place on new motor. Entire procedure
... Read more
very easy.
Read less
Was this helpful?
Thank you for voting!
2 burned out bulbs under the microwave/important light source for kitchen stove.
-
Ferol from San Antonio, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.
Was this helpful?
Thank you for voting!
replace filter
-
Barbara from Cranston, RI
- Easy
- Less than 15 mins
slide into place under hood
Was this helpful?
Thank you for voting!
burnt out light bulb
-
Shirley from Londonderry, NH
- A Bit Difficult
- Less than 15 mins
-
Screw drivers
The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.
Was this helpful?
Thank you for voting!
Bulb burned out
-
Lester from Mesquite, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.
Was this helpful?
Thank you for voting!
Broken plate
-
JASON from ABSECON, NJ
- Really Easy
- Less than 15 mins
Took the replacement plate out of the box and put it in the microwave in seconds. I never realized how much of a difference having the correct microwave plate would make. It's great to have it back.
Was this helpful?
Thank you for voting!
in 2 yrs the charcoal filter had NEVER been changed and it was smelling horrible--so had to be done !
-
carole from North Canton, OH
- Easy
- Less than 15 mins
-
Screw drivers
--simpley removed 2 screws, removed old filter--but had PLENTY of cleaning to do before putting in the new filter !My husband LOVES to cook and pan fry foods--it won't go that long before being replaced in the future!
Was this helpful?
Thank you for voting!
Needed a clean filter
-
Ethel from New Berlin, WI
- Easy
- Less than 15 mins
-
Screw drivers
Stood on a step stool (microwave over stove), took off the one panel,removed old filter and put in new one
Was this helpful?
Thank you for voting!
Filter dirty
-
John from Denver, CO
- Easy
- Less than 15 mins
-
Screw drivers
I unscrewed the filter cover, replaced the charcoal filter and replace the cover. The other wire mesh filter slides right into place. You sent me the right parts for my filter replacement on my microwave. Easy install. Thanks
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken turntable support ring and missing support
-
Sharon from Pleasanton, CA
- Really Easy
- Less than 15 mins
Watched video which reminded me to order support for the turntable support ring and did exactly what the person in the video did. Excellent and prompt service and all parts fit.
Other Parts Used:
Was this helpful?
Thank you for voting!
glass turn table would not turn
-
CJ from Bullard, TX
- Really Easy
- Less than 15 mins
After researching online, I found that I needed the turntable drive coupling, part#PS993087. when I went to your site it showed the same part but the part number had changed but said it would fit my microwave. Well, I was really surprised and happy when the part I received 3 days after I placed the order, with normal shipping,fit perfectl
... Read more
y and now my turn table in my microwave works. I have marked this site a a favorite and will use it I'm sure soon. Being a single women and having to figure out how to fix the things on a small buget, I'm learning a lot and have a lot of respect for men that know how to do all the repair stuff. Thanks so much, I have been able to mark this off my list of things to fix. Have a nice day. Cj- age, 58
Read less
Was this helpful?
Thank you for voting!
The capacitor was melted in the microwave
-
Jocelyne from Fort Pierce, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
My husband open the microwave and see the capacitor melted. He try to find the piece in store,but unfortunatly he didn't find any. I found the piece on the web and ordered it. My husband replaced the part easily. The microwave work very well.The microwave was to our friend. He did replace it by a new one. Now we have a new microwave with
... Read more
a fan.
Read less
Was this helpful?
Thank you for voting!
Broke glass tray
-
Katherine from Cleveland, TN
- Really Easy
- Less than 15 mins
Arrived in 24hours!!! Great.
Was this helpful?
Thank you for voting!