MLE19PNDYW Maytag Washer Dryer Combo - Instructions

first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of the front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job.
Thank you.

As Typical with this Neptune front load washer, the Water Seal fails to keep water from getting into the bearings. The bearings start to sound like a jet engine at high speed spins once the grease is washed out (nice grease splatter at the back of the cabinet). You can replace the Lip Seal but the bearings are not part of the kit. It is a waste of time to replace the seal kit if the bearings are already bad or going bad. You can't buy the bearings from here or any other appliance part store. You have to purchase a new tub in order to get new bearings, at $500+. Not worth it. I purchased the Lip Seal Kit with the intention of removing the bearings and replacing. The instructions that come with the kit explain with diagrams how to disassemble. In order to remove the spinner from the outer tub, I had to remove the whole tub, place it face down on some 2x4's and hit the spinner shaft with a hammer and block of wood to get it out of the old bearings. It came out fairly quickly. I removed the old lip seal (you can use the two access holes at the back of the outer tub to bang out the lip seal with a nail) and using a hammer and screwdriver, banged out the front bearing in the outer tub from the back and through the back bearing. This took a little while of moving around the bearing edge and tapping out, especially since there is a pipe spacer between the 2 bearings. It can be moved partly out of the way. The spacer will fall out with the front bearing. I then removed the C-clip that holds in the back bearing and banged out using the same method as the front bearing but from the inside. It too took a lot of tapping around the edges due to lots of corrosion. Once I had the bearings out, I looked up the make and model printed on the covers. Order using a DDU designation which is a rubber seal on both sides, like originals. I cleaned up the bearing mounting surfaces using a dremel tool and wire brush attachment. Make sure you get the metal free of any contamination. Use grit paper if necessary. I also sanded down the spinner shaft and got the spindle nice and shiny. I inserted the larger front bearing first (use a little grease on outside edge), it was a very tight fit and had to tap in using a hammer and metal rod. Make sure it is all the way in. Install the new seal kit (mine was the crummy original design, not the revised one). With the spinner tub on the floor shaft up on some 2x4's (light coating of grease on shaft), place the outer tub over the spinner with the shaft inserting through the new bearing and out the back. The shaft isn't an interference fit with the front bearing so it should slide in easily. WIth the shaft fully inserted, install the pipe spacer (cleaned up) then place the back bearing (outside edge greased) over the shaft and into the outer tub. This is an interference fit and will have to be tapped into place. It also was a tight fit into the tub. WIth it part of the way into the tub, I installed the belt pulley and tightened it down using a longer bolt than supplied, and this pushed the bearing the rest of the way in. I then installed the the C-ring. Not sure why the C-ring is needed with the bearing being such a tight fit. I installed the tub assembly back into the washing machine cabinet and installed the pulley and belt.. After reassembling the complete washer (after much cleaning of dust and soap scum, etc) I ran the unit once with no clothes to make sure any contaminates (grease, etc) where washed out first. So far so good, nice and quiet. If it last me another 5-10 years I will be happy. It will fail again for the same reason since I had to use the same lame seal kit and didn't have the revised version un

Unplug and turn off water.....Removed belt drive cover. Rolled belt off of pulley. Removed pulley from back of splined shaft. Removed front door and front panel. Removed two screws that hold top of washer down, 4 screws that hold detergent/bleach tray to top and tilted top back. Removed 4 screws that hold door seal assembly to frame. Popped clips from back of seal away from outer drum. Note locations to reinstall. Pulled small hose away from seal assembly (located at bottom of door seal. Removed door seal assembly. Removed torx screws from tumblers in inner drum to access nylock nuts that hold inner drum to spinner. Removed inner drum. Pulled spinner shaft from outter drum. Removed seal from inside outer drum where shaft passes through bearings. Knocked outside bearing out with drift from inside outer drum. Be careful no to nick/scratch bearing fit or shoulder. Go to the back of the machine and knock the inner bearing out using same method. TAKE YOUR TIME. Outer drum 600 bucks, so don't mess it up. Bearings are available at local bearing shop. NSK 6206DU and NSK 6207DU. Cleaned well and made sure that bearing fits were in good shape. Cleaned up spacer that fits between bearings. Note the way it comes out of the bearing holder (it is tapered on one end). Tapped outer race of inside and outside bearings into fits (barely) after lying the spacer between the bearings in the bearing sleeve. Used threaded rod and some washers of the proper size to pull bearings together. Tapped outer races to make sure that they were seated. Check spacer sleeve fit between inner races (hold it up in the proper location with your fingers....should be snug. Pressed new seal in per directions. Trial fit spinner into bearings/spacer. Installed pulley and belt. Note how bearing spacer and shoulders and pulley clamp inner races together so that you don't get any slip/slop/slap. Reassembled in reverse. Only problem I had was with the door latch manual releast that I accidently clamped between the bleach/detergent dispenser and lid when closing it up....had to adjust. Drank beer and bragged to wife. Been about 20 loads no....no leaks and as quiet as it was new. Took about 2 hours to take it apart and about 3 to put back together....Not a bad job. Definitely cheaper than an outer drum assembly.

removed door, removed screws to lift top panel, removed screws that held old baffles, replaced with new baffles, took off front panel and cleaned out excess lint while I was in there.

FIRST unplug dryer from electrical source, CAUTION, the top of this dryer does not open with clips, do not pry on top to open! On the front of the dryer look under the lower panel, and find two screws, one on the left side, and one on the right, remove these screws, and pull slightly down on panel to remove. Behind this panel find two screws holding the door panel, one on the left, and one on the right, remove the left, and support the door panel while removing the right side. Gently pull the bottom of door panel outward, and the clips on top of door panel will unhinge from top, carefully rotate left side of door panel to floor, and note the wire connections on switch, and orientation of switch, then unplug wires, and move door panel to a comfortable working positon. Door must be open to remove switch, then depress the two plastic retaining keepers on each side of switch, and push switch through toward door. Replace with new switch, reconnect the wires, and reassymble in reverse order. Remember, door assymbly must be inserted in dryer top at an angle, and then bottom rotated downward, and bottom panel nylon guildes inserted into door panel bottom.

First- I unplugged and completely drained machine of water by putting hose at ground level near drain . Second- removed back plate to washer saving all hardware. Third- disconnected in and out hose to pump. Twisted pump gently as to pop it out of slots in bottom of machine. Fourth- disconnected wires to old pump hooked to new pump replaced pump, replaced hoses- tested machine then replaced back plate of machine. Done.

I've never even opened this dryer before so I looked at one of the installation videos PartSelect has. I found one using my model, which made it really easy. I removed the front panel and door, then lifted the top of the dryer up on it's hinges: that's a great feature because you need the top out of the way to remove the drum. I took the belt off the drum, lifted it up and pulled it straight out. I did buy a pair of snap ring pliers to remove the snap ring off the drum support shaft. I think you really must have those to remove and replace the rings. Be careful when removing the snap rings. I shot the first one across the room like it was a rubber band. We had a good laugh. I used a wrench to hold the nut on the backside of the roller shaft and unscrewed it. I screwed the new roller shafts on, slipped the drum rollers on them, then carefully used the snap ring pliers to place the rings on the front of the shaft to hold the rollers on. While I had the unit opened up, I figured I should go ahead and replace the multi rib belt. I put the ribbed side on the drum and sat the drum on the rollers . The tricky part is now getting down on the ground, reaching under the drum for the belt. Make sure the belt isn't twisted anywhere on the drum or in your hands while you pull the belt under the idler pulley. Hold the belt ribbed sides together while feeding the belt under the pulley. It takes a good deal of strength to move the pulley over so you can hook the end of the belt on the shaft. Once you've gotten that attached, put your hand inside the drum and rotate it a few times to make sure you connected it properly and that you placed the belt in the right spot on the drum. It was easy to see the black stripe around the drum where I'd taken off the old one.

I used my screw driver to pry the old female end of the latch from the dryer unit. I forced the new female part of the latch into the hole and bang...45 seconds later the door closed securely --like new!

My repair (replacement of Maytag Neptune front load washing machine tub bearings) went well — knock on wood. The reason I took on the job somewhat confidently is I read online (probably from your site) the testimonial of someone who successfully did the same repair I faced. It is this persons sharing the recount of what it takes to do this job that gave me the motivation to take it on. For me it was around an eight hour job being my Neptune is a stackable (with the drier ontop). It has been a week now of operation with about 10 loads through the washing machine. It is sooo nice not listening to the previous worn bearing sound best described as a jet plane winding-up during taking off coming from the washer during its spin cycle. I pray the shaft seals stay snug. The job definitely was a major undertaking. Replacing the seal and bearing myself I saved probably saved $900.
Scott

Opened the back panel of the washing machine. Removed the old belt and wrote down the part number. Shopped online for a suitable replacement and found a perfect match at part select.com. I put in an order and it was delivered in a couple of days! I opened the back panel of the washing machinie again. This time I decided to also replace the isolators that came with the kit. For this, I had to unscrew the motor and gently tug it free. I placed it on the floor of the washing machine. I then replaced the 2 isolators as described in the kit, reinstalled the motor and put the screw back on. I then proceeded to place the belt on the motor and on to the wheel. This took couple of tries to get the grooves right. I then tested the washing machine on a rinse cycle and things looked good. Its been working fine so far.

If your dryer is squeaking it is most likely either the idler pulley or drum rollers. First I took apart the dryer to see which parts I would need. I checked the drum rollers by spinning them with my hand to see if they spun freely and also checked them to see if they were loose, they were okay. Then I checked the idler pulley and found my problem, it was hard to spin it so I figured the bearing was shot. I sprayed some lubricant on the bearing to help with the squeaking while I waited for my parts. It took about 30 minutes to diagnose my problem and put the dryer back together.
I took some advise from another story saying to get the whole idler arm, shaft and pulley assembly. It might have cost me a few bucks more, but I did not want to run into the same problem he did (the pulley bearing was fused to the shaft). It took me about 20 minutes to take apart the dryer, install the part, and put it back together. If you are pretty good with fixing things, you should have no problem doing this repair.

After taking the dryer apart, I found that one of the drum support rollers was barely hanging on the pin and was the main cause of the metal on metal squealing noise that became increasingly worse over a month's time.

I replaced both rollers, the idler pulley, and put on a new belt after giving the dryer a thorough cleaning.

It was a 100% success and fixed the problem making the dryer work and sound like brand new again.

This kit came with instructions. I followed them closely. The only thing I could add is clean the tub spindle with steelwool to remove any debris or rust. then wipe down spindle to remove all steelwool particles and follow instructions to reassamble.

take 2 phillips screws out where door meets drier. remove door, set aside. take 2 phillips screws out on other side, set screws aside. remove front of drier by pulling on top left and right sides, front of drier will fall twards front of drier. when it touches the floor lift up on bottom. set aside for later. put new baffels in (you can see where the old ones went) put screws in from bottom 5/16nutdriver. tighten. put drier front back on . start at bottom , snap top back in on both sides. put two screws back on left side, put door back on and replace 2 screws ( door will not go on wrong) test and your done...

The repair was easy, based on the comments from this website. I used a 6-in-1 screwdriver, and that was the only tool. I removed the two screws holding the hinges, removed the door, then the two screws on the opposite side of the opening. This allowed the front panel to come off. I spun the dryer tumbler until the baffle that was loose was at approximately 5 o'clock. I unscrewed the remaining screw and found the missing screw in the bottom of the dryer. I put those two screws into the new baffle, and popped the front back in place. I reinstalled the four screws (two opposite the hinge, then the two that hold the hinges)...all done in about 20 minutes (including vacuuming the lint out from that lower area).