MHWE950WW02 Maytag Washer - Instructions

This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol ... Read more oring refer handles. Thank you

I replaced the pump thinking this was the most likely cause of the problem. The pump is easy to access and get to. The reviews were helpful. The hose clamps were difficult to get back in place especially the one from the washer drain to the pump (need wide-jaw pliers). Now that I have seen the system work, the pump was not bad and the ... Read more water from the drain still smells bad. I just ordered the filter 8181683, which looks like the only other thing that would prevent the water from draining completely. The drain hose is not blocked.

Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs ... Read more will be purchased here.

Washed three loads and it was ok but then it stopped draining again. I don't know what to do.

I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you ... Read more loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw

Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.

Followed video clip that I found online

Opened lower front panel to access the motor controller. Took a picture of the wiring attached to the front of the controller. Removed two wiring harnesses and one wire with a retainer clip. Removed the faulty controller. Inserted the new controller, replaced the wiring, using the picture to insure correct positioning (although that r ... Read more eally wasn't necessary because the wiring clips could probably only be put in the correct places). Replaced the front cover, plugged in the washer and fired it up.

It was a little difficult to put the new Bellow in place on the tub, due to the fact you have to basically push the outside of the Bellow all the way into the tub so you can install the tub clamp. The other difficult part of the task was tightening up the clamp it's self. There really isn't a lot of room to move your hand around in the sp ... Read more ace you are given to work. But after a few hand cramps and a few things said, that are not needing repeated, I was able to get the clamp tight. Once you have the clamp on the tub, it's basically pretty simple to slide everything else into place. The wire/spring clamp that is used to attach the Bellow to the front of the washer is fairly simple to put into place with a little patience. All in all it was a cheep and easy repair for a due-it-your self repair.

I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.

pulled the front and top of the machine off, pulled off the old bellow, ordered the new bellow, and put the new bellow on. we looked on youtube.com for a video on repairing the machine.

Found it impossible to get the bellow off the machine. Removed the front spring. Even tried to but off the bellow. No luck. Called repairman. He had to take off the front panel, door panel, and the top of the machine before he could remove the back spring/clamps.

Followed video, slowly. Was easier then I expected. Everything fit perfectly.