MHWE500VP01 Maytag Washer - Instructions

First unplug the washer. Make sure and drain washer completely. If not drained remove front panel , Remove 2.5 inch Plastic drain cover which has a catch bin on it. This will allow it to drain the washer. Put pan underneath to catch the water. Tip washer back and prop up with something 6 inches tall to get to the screws underneath. A cement block would work well. Use pliers to squeeze hose clamp together to remove the Hoses. Gently lift up The flip down cover Over the top of the wire harness Push in the tab on the wire harness, Gently pull back on the wire harness. Remove two mountings screws from the bottom of the washer. Slide the whole pump housing to the right and Lift up. Now the pump is been removed. Inspect inside the hoses For Debrie. Remove anything that is left in the hoses. Reinstall the pump in reverse order from the way you took it off. Leave front panel off Make sure all hoses and wire harness are hooked up. Run wash cycle to make sure there are no leaks. Do not put hands in while running. If no leaks replace front panel. Not sure if this is the right way But this is the way we did it and it worked well. Washer runs quieter now than it did when we got it

Put towel down to catch excess water, opened drain screen, used pliers to remove squeeze clamps on both hoses, removed front hold-down torx-head bolt and slid pump assembly out. Compared new part to old and found 2 differences 1:no hold-down location in front for bolt,2: the rubber padded feet are not the same. I was able to remove the two screws on the right side and use just the rubber pad for support while sliding the left side in the slot and is was plenty stable and works just fine. I guess the Whirlpool Duet model is a bit different on mounting but everything else fit quite well, the washer is working perfectly again.

Just use the video. Shows you all you need to know. Very easy. Do it yourself and it saves you money.

We purchased a new pump and installed it very easily. My washer works great!

My dryer is on top my washer so I removed the dryer and pulled the washer out. I had to get rid of the water that was inside so I used my wet vacuum on the drain hose and sucked it out I then removed the front cover and the I tipped it back and removed two screws from the bottom of the pump bracket underneath the washer and moved the two clams on the pump hoses back to uncouple the hoses. I removed the pump and installed the new one and hocked everything back including the wires to the pump which is just a quick connect and pushed it back into place and it worked like new

Watched a YouTube video, saw how simple it was. Did all the things the video said to do. Then it said that if the error code came back, by the part. I bought the part SUNDAY night and it was under my door mat Tuesday when I came home from work. Removed three screws, took off the top of the washer, plugged the electronics, shoved the little hose on, put the top back on and boom, no problems! Now, if I could just find a YouTube on a Fisher Paykel dishwasher, I'd be in business... Great part, reasonable price, great service, great shipping.

open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.

Read the instructions provided by PartSelect.....and with a bit of patience I installed all four bolts so the washer's inside agitator was not damaged in shipping. I highly recommend that anyone who is moving/storing or shipping their washer that you find the correct shipping bolts according to your model and make and install them prior to moving your appliance.

Unplugged washer first! Removed front bottom panel by removing three screws, unscrewed the Drain Plug assembly by turning drain plug counter clockwise with a bucket to catch excess water from washer. Used pliers to remove spring clamps from washer agitator drain hose and then removed the spring clamp from the hose going to drain. Checked hoses for obstructions, then Slide Drain Pump assembly up to the right to remove. Then installed new Drain Pump assembly by sliding pump into slot to the left. Connected the agitator and drain hose to new Drain Pump and fastened with spring clamps. Plugged in AC line cord and turned washer on and started a quick wash cycle to check for leaks and to see if the water drained from washer properly. The water drained from washer and error code did not appear. The error code F21 reappeared during the second wash cycle. After closer inspection with a flash light, I found a large piece of cloth caught between the washer agitator and washer tub covering the drain by shining the flash light up towards the Agitator tub. This was solved by removing the Drain Pump assembly and all of the drain hoses again. Then removing the the large hose from the agitator tub and then removing the large piece of cloth from agitator tub. After reassembly, the washer worked like new!

Unplug washer. Open door. Look at the very bottom of the bellow and will see a spring that is connected to a small wire that runs around the bellow holding the outside on. Using a flat head screw driver insert it between the wire and bellow, pull down slighty. Grab the wire and gentley pull off. Now the outer part of the bellow will be free, pull it toward you, and off the water/soap despinser, then push it into the washer. Now look to the right side and you will see a screw head that is actully a big clamp ring around the bellow. This is the hardest part. Use a small rachet screw driver with a 7mm socket to lossen. Pull clamp off gently, you can now removwe the bellow. Put bellow back on in reverse. There will be a small tab on the bellow it goes to the top. Took about 2 hours.

We hired a local repairman and he even had trouble . I would not suggest anyone trying this installation on their own. It took the repair guy an hour to do and he struggled. Not an eary installation

First unplug the washer and take the back cover off. Loosen the screw on the motor and the big nut on the belt wheel. Take the old belt off and put the new belt on around the motor but slip the motor back in place with the screw slightly in place but do not tighten it yet. Place the belt around the motor and the wheel but this is hard because you need some one with some strength so the is where my dear boyfriend came in handy. He used his strength to stretch the belt and put it back on the machine so I could put the big nut back on. But if you break a wire you have to know a little electrical to put back the wires back in place with small connectors. I do know electrical also. My machine is working better like new. Carol Rozier

pulled the front and top of the machine off, pulled off the old bellow, ordered the new bellow, and put the new bellow on. we looked on youtube.com for a video on repairing the machine.

Searched internet for diagnosis. Ran diagnostic test using the diagnostic manual from whirlpool. The error code was F29. Replaced door latch but problem was not solved. Then order the Motor Control Unit. Removed old control unit through the top by removing the top washer cover and numbering harness positions with painter's tape. Install the new Control Unit and ran diagnostic procedure. The problem was solved. The washer is working fine.

Followed video, slowly. Was easier then I expected. Everything fit perfectly.