All Installation Instructions for Maytag Washer MHWE300VW13

Ripped bellowspul

Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.

Parts Used:

Washer Door Bellow

WILLIAM from REPUBLIC, MO
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Bellow was damaged,water leakage.

First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.

Parts Used:

Washer Door Bellow

Gopaul from Queens, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

5 of 8 people found this instruction helpful.

Was this instruction helpful to you?

The door bellows had a cut in it

I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.

Parts Used:

Washer Door Bellow

Arthur from MORGANTOWN, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Pump not draining the water out.

First I made sure the washer was unplugged from the outlet and I took out 3 screws that held the front panel and removed it to get access to the pump.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.

Parts Used:

Drain Pump Kit

Martin from Kotzebue, AK
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

PUMP HOUSING LEAKS

REMOVE AND REPLACE. FLEXIBLE RUBBER CONNECTOR WAS NOT A EXACT REPLACEMENT, THE ORIGANIL HAD A BACK STOP VALVE, NOT SURE OF THE EFFICATE ON MACHINE.

Parts Used:

Washer Pump Hose

Drain Pump Kit

JOHN from OMAHA, NE
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

5 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Replace Bellows between door and tub

Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip

Parts Used:

Washer Door Bellow

Gerald from Douglas, AL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

The part was made wrong and did not fit.

The plastic tabs were too large to fit into the washer's slotted hole in the washer cage. I initially bought this part from a PartSelect competitor and it was made wrong as well. Whirlpool themselves showed this part on back order so the faulty part originated in a Whirlpool order to a vendor. The reason for this reply is that PartSelect resolved this bad part issue within 2 hours and 1 phone call. The competitor has not resolved anything yet in 3 weeks and 5 emails with image proof.

Parts Used:

Baffle

Doug from ROCHESTER HLS, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Face Plate had broken off

Unscrewed two screws to remove old faceplate backer. Screwed new faceplate backer to detergent dispenser. Snapped new face plate on to the backer. 5-10 minutes tops.

Parts Used:

HANDLE

Mark from WEST FARGO, ND
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Pump not working

Replaced pump

Parts Used:

Drain Pump Kit

Darrell from Lady Lake, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

The video supplied by you was great and it worked very well.

It was fast and pretty easy to do.

Parts Used:

Washer Door Bellow

Michael from NEWBERG, OR
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Leaking water inlet hoses.

Removed the old hoses and screwed on the new hoses.

Parts Used:

Inlet Hose - 5 FT

Helen from NASHUA, NH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Broken hinge

Removed door from washer, remove hinge from door. Then slip in hinge and tighten hinge to door. Then attach door. It works and the most important thing the wife is happy

Parts Used:

Washing Machine Door Hinge

Anthony from JACKSONVILLE, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Hinge broke

We read your you tube instruction and followed the video

Parts Used:

Washing Machine Door Hinge

Lindsey from STEWART MANOR, NY
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

I was getting a sewer smell when the washer drained I did every cleaning technique and didn't solve the problem then I cleaned the inside drain hose and that helped so I replaced the hose and problem solved.

I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.

I replaced the hose and reinstalled the panels and I was done.

Parts Used: