- Home
- MH9115XBB0
- Instructions
MH9115XBB0 Whirlpool Microwave - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burned out light bulb
-
Ray from Gatlinburg, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
Replaced light bulb.
Was this helpful?
Thank you for voting!
Needed a new bulb under the microwave.
-
Norma from Unionville, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!
Was this helpful?
Thank you for voting!
burnt out light bulb
-
Shirley from Londonderry, NH
- A Bit Difficult
- Less than 15 mins
-
Screw drivers
The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.
Was this helpful?
Thank you for voting!
Burn't out bulb.
-
Carter from McCordsville, IN
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the glass cover and replaced the bulb. Very simple.
Was this helpful?
Thank you for voting!
Old filters were beyond cleaning
-
DAVID from ST. SIMONS ISLAND, GA
- Really Easy
- Less than 15 mins
Simply removed front of Microwave, removed the old charcoal filer and inserted the new one. On the grease filters, removed both of them from bottom of microwave and slid the new ones in place. That's all there was to it. No tools required.
Other Parts Used:
Was this helpful?
Thank you for voting!
Bulb burned out
-
Lester from Mesquite, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.
Was this helpful?
Thank you for voting!
Microwave worked intermittently
-
Robert from Palmer Lake, CO
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
The door was not engaging the micro switches properly no doubt from 10+ years of wear. The upper switch removed fairly easily but take care not to tweak the plastic brace too much or it will snap. The lower one was the tricky one. After much examination I noticed that the trick to remove it was underneath the brace. Take a butter knife (n
... Read more
o joke) and insert it just under the old micro switch and gently press down twisting the micro switch every so slightly til it releases. The replacements snap back in with no trouble. The microwave is working much better now, though not perfect.
Read less
Was this helpful?
Thank you for voting!
Motor quit working but light and timer still worked.
-
Thais from La Grange, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked
... Read more
on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.
Read less
Was this helpful?
Thank you for voting!