MH6140XKB - Instructions

After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!

The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.

Replaced the diode (aka wire-vltge) in the HV circuit after removing cabinet cover using both the secure torx screw drvr & phillips head screw drvr. The hardest part of the job was finding the secure torx nut drvr tool on the internet & purchasing same.

Due to the way the appliance was installed, it was impossible to get to the outer vent grille mounting screws. My husband was finally able to pry the grille cover off with a screwdriver. I was finally able to clean the grille cover and replace the filter. The grille cover no longer fits as tightly as it should because part of it broke off, but it will do. The builder did not consider maintenance when installing the appliance.

removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.

Placed in micro Great sevice. Thanks

Great!! I set the new tray into the microwave and was done! This site has the best service I have ever seen! I'll be back when something else breaks, it is just a matter of time.

I unscrewed the light cover, removed the burned out light bulb and replaced it with one I ordered on Partselect.com. It was very easy.

Just took the plate out the packaging & rinsed,dried and put in the oven. I was so happy I found it @partselect online& it came in the next day or two. Will definitely use them again. It was a fraction of the cost from local parts store.

remove 4 screws from top, front louvered panel snaps out. remove 1 screw from top of keypad, keypad pivot's forward and can be removed. There is a white mounting bracket inside left. Remove two screws, one top and one bottom, bracket lifts up and out. 3 sets wires are attached, mark them with masking tape, top, center, bottom and pull out plugs. They can only attach one way. Using a very small screw tip, lift plastic latch from switch, it rotates out and is removed from the pivot pin. reassemble in reverse order after switches are replaced

I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.

It literally took me longer to unpackage the fuse than to install it. I removed the outer shell by unscrewing the five screws, lifted it off and set it aside. The old fuse was readily visible so I pulled it out and put the new one in its place. I set the shell back on and replaced the screws. I plugged it in and ran it for 30 seconds while still in the shop just to make sure that solved the problem and presto - it worked like a charm. A $20 part saved me from having to purchase a new microwave (sadly, I had to break the news to the wife).

I started by calling a reputable service company to diagnose my problem. The repair tech told me it was the magnetron and it was a "very difficult" repair that required two people because the over-the-range unit needed to be taken down. I asked for a detailed estimate. He quoted $550 including parts and labor. After he left, I researched the part costs on this site and realized his costs were very inflated. I purchased the magnetron for $220. It arrived at my door two days later. Installation was very easy. First, I unplugged the unit. Then, while my wife was making sure it did not fall off the wall bracket, I unscrewed the two mounting screws from the top of the cabinet. I lifted the unit down from the wall and set it on the kitchen counter. The shell needed removed from the microwave which involved about 20 screws. This provided access to the magnetron on top. The magnetron is secured by five screws and a plug. I unplugged it, unscrewed it, and removed the old part. Then, I installed the new magnetron, and tested the microwave to make sure this did the trick. It worked. I put the outer shell back on the microwave and cleaned the microwave. (This is a great opportunity to clean the areas you do not typically see!). I then remounted the unit and plugged it back in. Saved myself a bit of money so I took the family out to dinner and a movie to celebrate. Microwave was in working order for heating up left overs the next day! Thank you!!!

I received my glass cooking tray so fast but when I try to put in the microwave did't fix was to big,I call you today to return and very nice lady help me and told me I need to call whirlpool and explain them and already order again thank so much for all your help you have very nice people in customer service. Thank you so much again. !!

I simply went on line to Part Select, placed my order, made payment, and was astonished to see the package with a new dish sitting on my doorstep the next day.Great service.