MGR6772BDW Maytag Range - Instructions

Pulled oven out of the cabinet/wall and pulled sensor out and replaced with new one.

I ordered the door glass from Part Select, which arrived quickly and in good condition. I loosened two sets of screws under the bottom glass holder frame, removed three screws at the top of the door to give more room. Slid the glass in place, re-installed and tightened the screws.The stove door looks great and works great. Great customer service too.

A few years previously I had this same problem and a PROFESSIONAL had replaced the sensor.
Thus this time I knew what the failure was and obtained the sensor from Part Select. Having observed the PROFESSIONAL replace the sensor before; I followed his easy technec only to learn that when the sensor was pulled from the aft wall of the oven that the wires had deteriorated and the plastic plug melted. Therefore it was neccessary to remove the oven from the wall cabinet. Then I removed the panel from the back outside of the oven, cut back the wires and because the kit from Part Select contained additional connectors was able to splice in a replacement connector. Installed the new sensor and reinstalled the oven. LESSON LEARNED; when the PROFESSIONAL had replaced the sensor he had failed to feed the wiring and plug back past the insulated chamber, directly behind the oven, into the cool area assessable by the panel on the aft side of the oven thus the plug and wires were exposed to the heat of the oven. What would commonly be a few minutes job turned into an afternoon project.

Remove racks and pull out stove from wall. Remove back cover from stove. Unscrew and unplug sensor. Rethread new sensor wire through hole and plug in new sensor and rescrew plate that holds in place.

We had complications because of how the stove was installed, which delayed the "fix" time considerably.

Also installed ignitor. It was determined that both were bad. Gas would come on but not light. When oven would light, it would not re-light periodically to keep the temperature up, causing gas smell. This added time to repair of an additional 1 hour, and required removal of bottom drawer.

My oven stopped working and the display read F3 error. I looked up the code and found that it was probably the thermostat sensor. I ordered the part from partselect.com and when it arrived I went to install it but I ran into a somewhat scary issue. I found that I had to pull my oven out of the wall in order to replace the sensor.

After a minor nervous breakdown, I decided to go for it and found that it was much easier than I had imagined. Changing the sensor involves taking out the two screws that hold the sensor in place (inside of the oven), pulling it out to the point you can reach the connector, plugging in the new sensor and screwing it back in place. However, if you have an oven like my model, you have to pull out the whole oven from the wall in order to reach the plug on the sensor. This sounds like a lot of trouble but for me it was very easy. The oven is held in place with screws around the front side. Most are easily accessed and you don't have to take out any critical/complicated pieces of the oven. My screw gun made short issue of the problem and I found that the oven was out of the wall within minutes. I could then easily unscrew a small back cover, change the sensor and then screw the oven back into the wall. Being very careful, the whole operation took about 20 minutes. I recommend that you get help from a friend just because the oven is bulky. It is not heavy, an average sized male can handle the weight but it’s easier with a friend. Also, be careful that the gas hose which feeds the oven is long enough (and not tangled) for you to move the oven out of its space. Obviously, be careful about gas leaks.

Removed the old sensor by removing two screws and pulling the wire out through the hole. Disconnected the connector and discarded the old sensor.
Selected the correct connector of the 3 provided, plugged the new sensor in and threaded the wire back into the hole paying special attention to make sure wire and connector was on the backside of the insulation. Assembled the two screws and tightened.

removed panel from back 4 screws. unplugged ignitor wire to lower level of upper oven, top wire is for broiler.Slid oven door off its hinges(very heavy)removed wire rack removed 2 screws from bottom pan lifted out,lifted off burner guard, looks like it may have had nuts to hold it down at one time , mine were missing. lifted out burner assembly. removed 2 screws holding down ignitor, they stripped out had to drill holes slightly larger and install new one with screws and nuts I had on hand. Used long screw driver pushed in from behind to guide ignitor wire back thru the insulation. reinstalled everything in reverse and it worked like a new. $50 part part saved us $2000, we were looking at replacing it with a new oven but we really liked what we had. Very satisfied, and wont hesitate to tackle next repair job with help from this web site.

First, thanks to PartsSelect for getting the part to me so quickly. I went to the "Instant Repairman" , checked all that applied to my problem. The answer was the sensor, 99% of the time.I used a coat hanger to pull the latch back and open the door. I watched the video and followed the instructions to remove the old sensor. The wires were melted but the plug was still good. I used one of the adapters to install the new sensor, then replaced the two screws inside the oven. I pulled the stove out because I had read in the reviews that you needed to get the plug behind the insulation away from the oven wall. I was lucky ,there was a small hole in the back ,right behind the sensor.I gently pulled the wire and plug to the back ,well away from the oven wall. Put the stove back in place ,threw the breaker and was back cooking again!! My stove has a downdraft vent, took me longer to hook the vent back up than to install the sensor..Oh yes, did I say,I am a75 year old female and I did it all myself..

Pulled the oven away from wall to access rear of oven. Disconnect electric plug from duplex outlet, turn off gas supply ball valve. Removed two screws that retain sensor on inside of oven. Disconnected two prong sensor connector at rear of oven. Tied a length of string to sensor connector wires. Pulled old sensor out through front of oven. Use the string to tie onto new sensor connector wires and pull new sensor into place from rear of oven. Retain sensor with two screws. At back of oven, used connector jumper supplied with part package to make connection to existing connector.

The door trim is held in place by five (5) screws. First I removed the two (2) side screws and then the three bottom screws. Be very careful because the trim holds the front glass panel in place. The repair can be made without removing the front door of the oven. Just remove the bottom drawer to get to the bottom three screws. Took approx. 15 to 20 minutes to complete. That's because I took the time to clean the inside of the glass panel. Really easy!

Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires together and reattached sensor inside oven. A cakewalk.

Look in the oven. On the upper left corner is the sensor. Remove two screws. Gently pull the wire and connector through the hole and insulation. Disconnect old sensor, replace new. Gently push the connection through, then finish pulling through from behind the stove. Replace the screws inside the oven. Done.

I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its corresponding hole.

easy-peasy remove small panel on back
disconnect in the back of range-oven "orange wire"
unscrew igniter from burner inside oven
remove and replace with new one
slide wire thru hole in back of oven
reconnect---u r done
dave

place new ones in by hand. the new ones fit too loose and if not carefull they will fall out.