MGR6751BDW17 Maytag Range - Instructions

Remove two screws back panel and remove sensor two screws inside top oven.

Simple process. Pull the unit out approximately 6 inches. Remove 2 phillips head screws on the left side panel which is about 3 inches wide and runs from the top to the bottom of the unit. No need to remove the panel on the right. Two hex head screws hold each hinge in and are visible once the oven door is removed by opening the door about 20 degrees and lifting it off the hinges. Once the door is off, simply remove the two hex head/self tapping screws holding each hinge in place and remove the hinges from the rear of the front of the oven. Reverse the process to install the new hinges. Do not over tighten but remember they are self tapping and need just a bit of tightening until the hings feels solid. Replace the door by sliding it over the hinges and you're done.

unscrewed screws in the back of the stove. inside the stove, replaced the old bake igniter with the new one and connected the electrical wire in the back of the stove.

First of all called my local appliance stores and was told that no one had parts because the range was too old. My husband was adamant that we needed a new stove. After much searching found a part on your site. The repair was soo easy a mere woman can do it. Required a screw driver and patiently taking the door apart. Could have been done faster if I had not cleaned everything back to new condition. Easy repair. . . Awesome service from your company!

Just remove the old for new

Removed the two screws pulled the element out and unhooked the wires then used one of the included adapters to reinstall the new sensor then screwed the two screws back in to secure the sensor. Everything works fine now.

I took out the old and replaced with the new. The hardest part was getting that tiny halogen bulb in that tiny little hole. It took longer to take the oven racks out and put them back in than to make the repairs.

removed oven door, unscrewed 2 screws on front of plate covering burner at bottom of oven. Undid wing nuts on tent-like cover, unscrewed 2 screws at back of burner (igniter "hiding" under left back side). Pulled oven away from wall (yuch, where did that stuff come from?), unscrewed 2 screws of bottom plate, undid connector to old igniter, fished wires with connector from new igniter, plugged them in. Attached new igniter to bottom of burner, rescrewed. Put all screws and parts back in correct places. Cleaned oven door before putting it back on. Turned oven on........baked bread!! Hooray! Repair was easy-peasy!

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

I disconnected the electrical power, but not the gas line, and pulled the oven unit away from the wall. I unscrewed the old temperature sensor mount and only realized then the simple configuration: A wire from the sensor runs through the back of the internal oven space to the back of the oven unit through a thin space filled with insulation. The old sensor was easy to disconnect behind the oven unit and pull the old sensor and wire forward through the opening in the oven. The most challenging part was threading the new sensor wire from the oven interior through the back of the oven unit. The instructions and comments provided on-line by previous customers was EXTREMELY helpful. I wish I could do many more household repairs like this!

followed instructions and slid clips where instructed

Ordered the oven sensor. Two screws to remove to replace old sensor. Since this was a slide in unit, you had direct access to the wiring harness. Used the adaptor. Total repair time about 20 minutes. A very easy do-it-yourself project.

removed the door, removed the bottom, removed the glass. The handle bracket it attached to the door but though the vented part. After removing the old handle just had to put it all together again, Not hare just a lot to take a apart.

I unscrewed the door's top edge, removed the bottom drawer to loosen the oven door's bottom edge to where its screws were hanging in by a thread. The outside glass was then removable and exposed the screws holding the door handle mounting pieces. I unscrewed the four screws that held the mounts to the door, then the two that held the handle to the mounts, replaced the broken handle with my promptly delivered new one and reassembled the door in reverse order of above. Oh yeah, reading the other accounts of how to do this was the most important step in all this.

Slide oven door off hinges. Remove old gasket. Instal new gasket. Used eraser end of pencil to help feed in ends of gasket into respective holes for excess. Note: job could have been accomplished without taking off door but I wanted to take door appart to clean inside and out of glass.