MGR6751BDW17 Maytag Range - Instructions

Look in the oven. On the upper left corner is the sensor. Remove two screws. Gently pull the wire and connector through the hole and insulation. Disconnect old sensor, replace new. Gently push the connection through, then finish pulling through from behind the stove. Replace the screws inside the oven. Done.

I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its corresponding hole.

easy-peasy remove small panel on back
disconnect in the back of range-oven "orange wire"
unscrew igniter from burner inside oven
remove and replace with new one
slide wire thru hole in back of oven
reconnect---u r done
dave

Remove door, racks, unplug, remove lower burner cover two screws, the burner tube deflector pan two wingnuts, the burner tube. With igniter attached, remove back of range 4 screws to expose connector to igniter, unplug then remove burner tube, then igniter, replace igniter feed through back of oven wall and reconnect igniter reverse process and its done

. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor

Removed the door form the oven. Removed all screws holding the door covers. Removed all screws holding the handle mounting brackets and handle. oriented the new handle to the door and reversed the disassembly process.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then conected the new element and replaced te two screws. Turned on the oven & works fine.
Very Easy!

I first removed the drawer from under the oven, then I used 2 strips of packing tape to hold the front glass in place. Next I loosened the 4 screws on the bottom side of the door to the point just before they would fall out. Next I had someone help hold the glass as we removed the tape and slid the glass from under the handle and set it aside. Once the glass was off I removed the 4 screws on top of the door and the 4 screws (2 each side) holding the handle brackets. From that point it was just a couple of screws on the back of the handle to swap the broken part for new and reassembling everything. Could be done in 30 minutes, 40 by yourself. Maytag wants $24 to tell you how to do this, it's not worth the money. Also, PartSelect.com sold me the part for 30% than Sears or Maytag advertise - they've earned a permanent bookmark in my browser!

I removed door by opening it to first stop and lifted it up off the hinge's. I removed all screws that held the inner panel to the outer panel and handle. Removed inner panel from outer panel, then glass and insulation, replaced glass and insulation and panel.

Replaced screws and handle,pulled hinge's out to first stop and slid door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.

PS: shipping was fast and price was great.
Thanks Bob G.

I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.

After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now just like a new oven.

Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...

I unplugged the power cord,removed the back panel and unplugged all the wiring harnesses.four screws hold the control in place. reverse to install. The instructions were very complete(I do this for a living so it was extra easy)Anyone following the directions could replace this in under 15 min.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I had the old oven rack in the oven when I cleaned it. The rack came out brown and would not slide easily. The new rack was exactly the right one and now all is back to perfect!