MGR6751BDW Maytag Range - Instructions

Removed the door form the oven. Removed all screws holding the door covers. Removed all screws holding the handle mounting brackets and handle. oriented the new handle to the door and reversed the disassembly process.

I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

I first removed the drawer from under the oven, then I used 2 strips of packing tape to hold the front glass in place. Next I loosened the 4 screws on the bottom side of the door to the point just before they would fall out. Next I had someone help hold the glass as we removed the tape and slid the glass from under the handle and set it aside. Once the glass was off I removed the 4 screws on top of the door and the 4 screws (2 each side) holding the handle brackets. From that point it was just a couple of screws on the back of the handle to swap the broken part for new and reassembling everything. Could be done in 30 minutes, 40 by yourself. Maytag wants $24 to tell you how to do this, it's not worth the money. Also, PartSelect.com sold me the part for 30% than Sears or Maytag advertise - they've earned a permanent bookmark in my browser!

I removed door by opening it to first stop and lifted it up off the hinge's. I removed all screws that held the inner panel to the outer panel and handle. Removed inner panel from outer panel, then glass and insulation, replaced glass and insulation and panel.

Replaced screws and handle,pulled hinge's out to first stop and slid door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.

PS: shipping was fast and price was great.
Thanks Bob G.

Clearly, the oven gasket was not the cause of the problem.
The hinge replacements did not fix the problem. I think the problem was that the hinge's mating part inside the door had been deformed, perhaps by leaning on the door when fully opened. I compensated for that by placing two stacked magnets near the upper hinge mounting screw hole on the inside of the oven body. (0.75" screws , 8-24 or metric equiv., needed for the upper screw location.) This gave the hinge about 15 degrees of additional door tilting force. In addition, I added 6 ceramic magnets across the top of the door mating surface, kudos to that website. Now it pulls fully flush with the magnets.
Ceramic magnets are good to 400+ degrees and they come in boxes of 120 for $12.00.
I only had one oven as a sample, but I could see what I thought was deformation on the inside of the oven door where the hinges are inserted. In this case, I think that makes (only) hinge replacement futile.
Sorry if this solution does not fit your marketing desire, but I did leave the new hinges installed.

I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.

Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...

After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now just like a new oven.

I unplugged the power cord,removed the back panel and unplugged all the wiring harnesses.four screws hold the control in place. reverse to install. The instructions were very complete(I do this for a living so it was extra easy)Anyone following the directions could replace this in under 15 min.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I had the old oven rack in the oven when I cleaned it. The rack came out brown and would not slide easily. The new rack was exactly the right one and now all is back to perfect!

Removed old ingniter with screwdriver. Installed new igniter, but had to remove connector in order to electrically connect using twist on connectors.

needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks

Be prepaired to take the glass out. Unexpected, but not too hard. A right angle screw driver can be helpful for the bottom door. Takes some skill and patience. Good Luck! I am happy with the parts. Delivery time was quick.

Remove outer panel first, outer glass and handle come off as one piece. Be carefull to secure as last screws are removed. Remove inner silver panel. Remove broken glass and replace with new. Reaassemble. Around 10 Phillips head screws altogether. Much easier than I thought