All Installation Instructions for Maytag Range MGR6600FB3

Oven temperature was WAY off, sometimes 50 degrees.

Turned the breaker off. Removed the racks, pulled the oven out and removed the back. Disconnected and unscrewed the old sensor from the back, connected and screwed in the new one. Returned the racks and slid the oven back in.

The only remotely challenging part was disconnecting the old sensor. I had to figure out where to press with the flat screwdriver to get it to release.

I had found a good YouTube video and didn't use the app.

Parts Used:

SENSOR

Sarah from Raleigh, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replaced screw

By hand screwdriver

Parts Used:

Screw

Judith from SALEM, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Gas oven interment lighting. Pan was cracked and out of shape.

Loosen top two rear screws from the top pan. Remove top pan
Remove 2 front screws from bottom pan. Remove bottom pan. Reverse order.
Replace both pans.

Parts Used:

BAFFL-BRNR

Teddy from PRAIRIEVILLE, LA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Had lost one of the drawer glide

Just attached the glide to the drawer. It just popped in. No problem.
took about 5 minutes.

Parts Used:

GLIDE-DRWR

Lydia from SAN ANTONIO, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Paint peeling from strip

removed 3 screws holding the strip and replaced with new strip

Parts Used:

Trim, Lower (White)

Myron from Punta Gorda, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

last oven bottom was ruined by melted and burnt plastic

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

Parts Used:

Interior Bottom Oven Panel

Dennis from Missouri Valley, IA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Corroded/greasy bottom oven tray

Loosened two screws and removed tray, very simple. Replaced new tray and adjusted screws to hold tray. Easiest part was finding new tray part number and ordering replacement using online parts diagram.

Parts Used:

Interior Bottom Oven Panel

Robert Ruth from FERNDALE, WA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

screw came off

very expensive to buy the part but just tighten the screw intot eh predefined place.

Parts Used:

SCREW

Sandeep from EDINA, MN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Pan scratched by housekeeper

Unscrewed old pan and screwed on new one.

Parts Used:

Interior Bottom Oven Panel

Kenneth A. from SANGER, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Front glass shattered, side trim broke and lower trim bent beyond repair

Followed the YouTube video and did it the correct way they showed. Note: side trim goes under the glass.

Parts Used:

Outer Door Glass - White

Trim, Lower (White)

Daniel from CEDAR SPRINGS, MI
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broiler pan missing

ordered new broiler pan

Parts Used:

2 Piece Broiler Pan

RAYMOND from JACKSONVILLE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

door of oven came apart when plastic screw holders broke

put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!

Parts Used:

Screw

patricia from chipely, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom Door Trim Rusting

I remove bottom trim which is held on by 3 screws and try to install new bottom trim, did not work well. I then remove yop handle assem. Then the door glass which you need to clean after. Then install the new bottom trim then insert the glass into the new bottom strip using masking tape to hold the glass and side strips in place prior to installing the the top handle piece which is held on by two screws. Not a hard job to do.

Parts Used:

Trim, Lower (White)

Dennis from Grimsley, TN
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Oven Self Clean Would Not Function

Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !

Parts Used: