MER6741BAS17 Maytag Range - Instructions

Remove top by opening oven and taking out two screws in the front. Lift up top and unplug wire connectors on bad element, writing down where they are landed. Take out screw on element bracket and replace. That easy. Be sure to unplug appliance for your safety. :-) Also just wanted to add that PartSelect was great. Ordered it on saturday and was cooking with it on tuesday. Great job.

Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

Purchased 2 piece broiler pan from this site

glad I found you on line, it was very easy to replace the handle and saved me money because I didn't have to have a service tech come to my home.

I removed the two small screws, gently pulled the element outward, slid the wire connectors off the ends of the element legs and reversed the process to install the new one. THE ELEMENT STILL DOES NOT HEAT. There must be a bad switch or thermostat at the ON switch area. That will be checked out by a Repair man as soon as I can get a schedule from him.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

I removed door by opening it to first stop and lifted it up off the hinge's. I removed all screws that held the inner panel to the outer panel and handle. Removed inner panel from outer panel, then glass and insulation, replaced glass and insulation and panel.

Replaced screws and handle,pulled hinge's out to first stop and slid door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.

PS: shipping was fast and price was great.
Thanks Bob G.

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

I pulled the range out, unplugged it and removed the back panel with a Phillips-head screwdriver. I then removed the two screws inside the oven that holds the element in place. I located the two wires on the back of the range attached to the element. I gently pulled off the wires using a pliers and then easily removed the burned out element. I put the ends of the replacement element into the respective holes, screwed them in and then plugged the wires back on at the back of the range. After replacing the back panel, I plugged the range back in. I turned the oven on with an oven thermometer inside, to test it out. I imagine I saved at least a couple of hundred dollars for the repair with this simple DIY, if not, the cost of a new double oven range!

Shut off power to stove. Moved stove out. Loosened screws in top and middle back of stove and removed cover. Took mental note of color order of each wire and unhooked each wire from old switch and reattached to new switch in exact order of color of wire as original. Remounted cover on back of stove and reattached screws. Turned on power and turned on burner and tested burner for heat. Turned off burner, slid stove back and bingo - done. Saved a lot of money.

Remove outer panel first, outer glass and handle come off as one piece. Be carefull to secure as last screws are removed. Remove inner silver panel. Remove broken glass and replace with new. Reaassemble. Around 10 Phillips head screws altogether. Much easier than I thought

Turned off breaker to oven, removed racks, unscrewed the plate holding the element in place, and pulled out the wires a few inches. All easy and fine to this point. Never having done anything like this before, I wasn't sure HOW the element was attached to the wires, so tugged on them a bit, but nothing budged. Got a flashlight (it got dark in there with the upper part of my body in there)looked again, but still couldn't tell. Referred to this site and saw reports of "plug and play", went back and examined the ends more closely on old and new element, realized that they slide straight on and straight off in a "sleeve". Got some pliars and pulled the ends apart. Slid the new end on to one wire, but couldn't get the other one on until I realized I had crushed it a bit with the pliars. Reopened the "sleeve" with a vegetable knife and slid the other end of the element into the "sleeve" at the end of the wire. Then pushed the wires back in and screwed plate on. It took about 23 minutes, and that included time to look up this site and do some reading, jump up to find a flashlight, and jump up and find a pair of pliars. My hubby was out of town for 3 weeks and suggested I wait til he got home--glad I didn't wait.

I had the old oven rack in the oven when I cleaned it. The rack came out brown and would not slide easily. The new rack was exactly the right one and now all is back to perfect!

Shipped on timely manner,I will order again from Part Select, installing was a 15 minute job, that what I did, 1 unplugged stove, 2) removed 4 screws, (2 on top bracket and 2 on back) , 3) slide unit out couple inches enough to disconnected the wires from each end of unit and removed old part, installed new unit by reconnecting end wires, pushing unit slowly toward back of oven until wires find it's right position, set it back in place with the 2 screws on top bracket and 2 screws on back, done!!