MER5875RCS Maytag Range - Instructions

I first removed the drawer from under the oven, then I used 2 strips of packing tape to hold the front glass in place. Next I loosened the 4 screws on the bottom side of the door to the point just before they would fall out. Next I had someone help hold the glass as we removed the tape and slid the glass from under the handle and set it aside. Once the glass was off I removed the 4 screws on top of the door and the 4 screws (2 each side) holding the handle brackets. From that point it was just a couple of screws on the back of the handle to swap the broken part for new and reassembling everything. Could be done in 30 minutes, 40 by yourself. Maytag wants $24 to tell you how to do this, it's not worth the money. Also, PartSelect.com sold me the part for 30% than Sears or Maytag advertise - they've earned a permanent bookmark in my browser!

First I released the lock on the oven door hinge so that I could take the door off by lifting it up and out. Then it was just a matter of removing screws, replacing the hinges, and putting it back together. I did have to guess a little as I started removing screws as I wasn't sure exactly what to remove, but it became pretty self evident as I looked it over. Not as bad as I had expected.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

looked for how to video on you tube. It saved me lots of money. Anyone could do it.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I wasn't sure if it was the heating element or the temperature probe not allowing the oven to go above 200 degrees so I ordered both from Selectparts. After receiving my replacement parts (in record time thank you) the oven element had a hidden slit on the underside near the connection. During its removal the element disintegrated at that point.

Since Maytag is very user friendly to maintain, it was a matter of removing the retaining nuts securing the element to the back of the oven, and resecuring after replacing with the new element. I did have to take the back panel off the oven to reattach the wiring to the element. This was necessary because while I was removing and replacing the element, the insulation was pulled through the access holes. I also replaced the temperature probe because I had already ordered it. This was easier to replace however and I did not encounter the isulation problem as I had when removing/replacing the element. I recommended your company to my friends and would definately order parts from you should I need to repair another appliance in the future. Thank you again.

needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks

Be prepaired to take the glass out. Unexpected, but not too hard. A right angle screw driver can be helpful for the bottom door. Takes some skill and patience. Good Luck! I am happy with the parts. Delivery time was quick.

took off nobs, pulled stove out 2 inches to access front side screws,( has 1 philip screw on each side end and four nut screws under panel) pulled panel out and flipped forward and down, all switches exposed and took apart broken switch and installed new switch(PAY ATTENTION TO WIRING PATTERN), reverse order for install back. bingo!

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

Had this range for 6 years. My daughter turned on the burner and it went "pop". She was very upset. I found the best price at PartSelect, and ordered the same day.

the first burner arrived broken in the box. We contacted PartSelect, and they immediately sent another and rushed shipping. It arrived in excellent condition.

To replace the unit: First, I turned off the circuit breaker for the range. Then I removed the two Philips screws that held the cooktop down. Next I removed the nut screws holding the burner to the cooktop.

Then I placed the new burner next to the old one, and one by one swapped the wires (this way I was sure I had the right wire on the right connector). One of the wire connectors broke when removing it from the old burner. PartSelect had provided 4 repacement connector pieces (oddly, all of which were too small for the burner element). So I located a replacement connector at a local hardware store. Stripped the end of the wire and used pliers to fasten the new connector.

After all connectors were secured to the new burner, I screwed the burner to the cooktop, then closed the cooktop and secured it with the two screws.

Turned on the circuit breaker, and it works like new! Saved over $100 by doing it myself!

See description listed as problem

After carefully removing the broken glass and cleaning the surfaces, I unscrewed the three screws holding the bottom metal panel using a Philips head screw driver. After replacing the existing double sided tape strips the replacement glass panel was evenly slid upwardly into place. The glass panel was held temporarily in place until the bottom metal bracket was slid upwardly into place and fastened into place by tightening the three Phillips head screws.

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.