Models > MEDB950YW1 > Instructions

MEDB950YW1 Maytag Dryer - Instructions

All Instructions for the MEDB950YW1
76 - 90 of 187
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Plastic retainer on catch was broken
Used screwdriver to remove old catch as shown via video from manufacture and snapped in new catch. Very easy to do and saved big bucks by doing myself.
Parts Used:
Door Catch
  • Larry from FRUITA, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not clisr
Had to force the old door catch out using the putty knife didn't work. Worked on it until I finally forced it out.
Parts Used:
Door Catch
  • LANA from INDIANAPOLIS, IN
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic part in door catch was broken so door would not lock to allow the dryer to operate
I tried to remove the part with pliers but could not remove it so I removed the screws that hold the front part of the door. I took the front part off, removed the broken plastic and then lifted on side of the catch so that the bottom of the front part came thru the door and then was able to remove the door latch. The installation of the new part took about 15 seconds to put in by pushing it into the opening where the broken part was removed. I put the front part of the door back and put the screws back and the dryer works fine.
Parts Used:
Door Catch
  • Henri from SILER CITY, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Latch Replacement
Used a screwdriver to pry out the bottom of the latch then the top. Pulled old latch out, then snapped new one in. Super Simple fix.
Parts Used:
Door Catch
  • Kathy from W TERRE HAUTE, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door catch on dryer stopped catching (meaning the door would not stay closed)
I placed the putty knife on the top part of the door catch and when that came loose I placed the putty knife on the bottom of the door catch and pushed on the putty knife and the door catch came out of its place. I then just popped the new door catch in place. Total repair time 45 seconds. The door now closes.
Parts Used:
Door Catch
  • John from AUBURNDALE, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lint screen tore and had a side that was loose so it didn't catch all the lint and cut your fingers
Removed the old screen and simply put in the new one
Parts Used:
Lint Filter
  • Wayne from ALBANY, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer won't start.Only make a click noise.
Remove top,front and panels.change thermal fuse and outlet thermistor.
Parts Used:
Thermostat, Internal-Bias
  • Candido from GREENVILLE, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Torn filter seal
Remove old filter, throw it away, replace with new filter.
Parts Used:
Lint Filter
  • James from SCOTTSDALE, AZ
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not close after I slammed it.
Simple with the Instructions in the video.
Parts Used:
Dryer Drum Support Roller Door Catch
  • Jeffrey from FRANKLIN, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heater element died
Pretty easy repair and I am not very handy. I believe they engineer these machines so you hire someone to do the job. They could place that part in an area where it is easier to get to, like a door on the side or something
Parts Used:
Dryer Heater Element
  • Jerry from AUBURN, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Catch broken
Took Putty Trowel and pried out top and bottom then pulled out with needle nose pliers, new part just pops back in (be sure flanges are on top and bottom not sides).
Parts Used:
Door Catch
  • Forrest from PARIS, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door wouldn't shut
Looked up on the internet, saw a video, ordered the part using model of dryer, got the part in 7 days, took out old part and snapped in the new door latch. Now it works good as new
Parts Used:
Door Catch
  • Jean from CARROLLTON, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door catch broken
Push in new catch...close door.
Parts Used:
Door Catch
  • ROBERT from GAINESVILLE, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F-26 Fault message
Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger
Parts Used:
Thermostat, Internal-Bias
  • DW from ALVIN, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door catch broken and fell into door
snapped new catch into door
Parts Used:
Door Catch
  • Phillip from FORSYTH, MO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MEDB950YW1
76 - 90 of 187
Back to Top