MEDB850WQ0 Maytag Dryer - Instructions

Remove top,front and panels.change thermal fuse and outlet thermistor.

Use the adjustable wrench to remove the water line. Remove the dryer vent line. Take off the screws on the main back panel, the screws connecting the top. Place both off the side. Unscrew and remove the parts connecting to the heat line located on the left side. Remove the front unit screw attaching the heat line to the bottom of the dryer. Remove the four screws connecting the top and bottom of the heat line together. The two on the left side is a huge pain, make sure you have small hands to be able to reach on the side of the line. Pull the bottom of the heat line loose. The heating element is inside the line. Replace element and put everything back in the order it was removed.

Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.

Removed the dryer door, unscrewed lint vent.

Remove old filter
Vacuum out
Install new filter

Just insert filter.

had no room to work in the back of the dryer

Easy manually

We have a very early model of the He3. We had to follow directions for the He2 model to replace the heater element and thermostat. Access is easy through the front panel, but removing and replacing the element required some force and maneuvering in a small area.

We replaced both the element and the thermostat since we had the entire part disconnected and removed. So far working great!

Dropped new filter in.

Exchanged old for new.

i removed the old lens,then removed the bulb,after ordering and receiving your replacement lense,it went back on just like the old one.the repair was very easy. thank you. D.S P.S1 IAM A REPIARMAN NOW!!! WITH YOUR VIRTUAL REPAIRMAN APP,VERY VERY SMART ILL SPREAD THE WORD.

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.

Ordered the fuse first hoping it was just that simple, watched the video for how to replace, first step was to take the back of the dryer off, well I order to take the back off I had to take off the Electrical Cord, as well as he top of the dryer. Only to find out he part I was replacing was not back there. Found the tech sheet attached within he dryer though, and as it turns out only needed to take he front bottom panel off. Without testing he continuity I was just giving this a shot, the Thermal fuse did no fix it, so I tried the high Limit Thermostat and Fuse kit still no luck. Took out the Element to find I was physically cracked in 2 pieces, replaced that and I was back up and running. And all parts were found in the bottom front panel of the dryer, so beware before you watch the video and take our whole dryer apart like I did.

The door catch dislodged in the door and apparently broke. The hardest part was getting it out of the door because in trying to remove it, the piece fell into the inside of the door. I could have easily just installed the new part (it snaps right in with great ease, that part took exactly 5 seconds). But hearing that old piece rattle around inside the door would have made me a little nuts. So I decided to take the door apart to retrieve it. It was just a bunch of screws from around the perimeter of the door, but I also had to unhinge it to do the job. Putting the door back together wasn't as easy as I had hoped, with some pretty tight fits and the glass dislodging. Had a few moments where I was regretting. But I got the old part out, snapped the new one right in. I'm sure an appliance guy would have charged me $60 - 90 just for coming out. Instead I repaired the dryer for the cost of a $3 part. One small lesson learned here -- dryer doors are much like refrigerator doors, or at least mine is. There is a door catch on both sides of the door so you can hinge it to open either way. I could have done the repair for nothing! But I love parts select for just this reason. I don't do major repairs, but replacing pieces on appliances couldn't be easier with this service!