MDE2301AZW Maytag Dryer - Instructions

first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of the front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job.
Thank you.

Removal of old lint collector and replace with new one.

No problem at all, just took out the old one in front and slid in the new one.

removed door, removed screws to lift top panel, removed screws that held old baffles, replaced with new baffles, took off front panel and cleaned out excess lint while I was in there.

FIRST unplug dryer from electrical source, CAUTION, the top of this dryer does not open with clips, do not pry on top to open! On the front of the dryer look under the lower panel, and find two screws, one on the left side, and one on the right, remove these screws, and pull slightly down on panel to remove. Behind this panel find two screws holding the door panel, one on the left, and one on the right, remove the left, and support the door panel while removing the right side. Gently pull the bottom of door panel outward, and the clips on top of door panel will unhinge from top, carefully rotate left side of door panel to floor, and note the wire connections on switch, and orientation of switch, then unplug wires, and move door panel to a comfortable working positon. Door must be open to remove switch, then depress the two plastic retaining keepers on each side of switch, and push switch through toward door. Replace with new switch, reconnect the wires, and reassymble in reverse order. Remember, door assymbly must be inserted in dryer top at an angle, and then bottom rotated downward, and bottom panel nylon guildes inserted into door panel bottom.

The door had always opened with the wrong swing and it wasn't til I needed to repair this that I noticed you could change the swing. I changed the swing of the door and then noticed that the clip was included on both sides so i did not need to repair the catch. I still have the part so when it breaks again, I can just pop it in.

I've never even opened this dryer before so I looked at one of the installation videos PartSelect has. I found one using my model, which made it really easy. I removed the front panel and door, then lifted the top of the dryer up on it's hinges: that's a great feature because you need the top out of the way to remove the drum. I took the belt off the drum, lifted it up and pulled it straight out. I did buy a pair of snap ring pliers to remove the snap ring off the drum support shaft. I think you really must have those to remove and replace the rings. Be careful when removing the snap rings. I shot the first one across the room like it was a rubber band. We had a good laugh. I used a wrench to hold the nut on the backside of the roller shaft and unscrewed it. I screwed the new roller shafts on, slipped the drum rollers on them, then carefully used the snap ring pliers to place the rings on the front of the shaft to hold the rollers on. While I had the unit opened up, I figured I should go ahead and replace the multi rib belt. I put the ribbed side on the drum and sat the drum on the rollers . The tricky part is now getting down on the ground, reaching under the drum for the belt. Make sure the belt isn't twisted anywhere on the drum or in your hands while you pull the belt under the idler pulley. Hold the belt ribbed sides together while feeding the belt under the pulley. It takes a good deal of strength to move the pulley over so you can hook the end of the belt on the shaft. Once you've gotten that attached, put your hand inside the drum and rotate it a few times to make sure you connected it properly and that you placed the belt in the right spot on the drum. It was easy to see the black stripe around the drum where I'd taken off the old one.

Just put the new one in. I also would like to tell you that I was VERY PLEASED with the service I received from your company. The part arrived very fast. Thank you very much. I will use your service again and will recommend you to others.

I used my screw driver to pry the old female end of the latch from the dryer unit. I forced the new female part of the latch into the hole and bang...45 seconds later the door closed securely --like new!

no repair needed but the part could not be found in the area i live . ordering was easy and deliver time quoted was very resonable but the part came the very next time that was wonderful.

took the front off by removing two screws took two screws out of element housing undon the wire and romeve element housing then romove the remaing parts that was needed on the new element then reinstall the element housing whith the new element in ti reinstall front of dryer and starting drying clothes project was complete

Very easy with a tip from the video that was provided from Parts Select.
Thank You
Joseph Errico

After checking power to the outlet, I removed the back panel to remove the Control Panel. Testing the timer shoed I had nothing leaving the timer (Door was closed and I held the Push/Start button at the same time. Ordered and replace new timer - still didn't work. Teseted the door button and found it corroded. Tried cleaning contacts and got it to work for a split second. Ordered Door Switch and Push/Start Button -just in case. Replaced door switch - dryer works fine!

I put the new one in . Nothing to it.

I removed front cover of dryer and found heating unit. I needed the detailed drawings from the PartSelect web site to help me find how to get the front cover off. It was easy after that changing out the sensors and reinstalling the heating unit.