MDB4949SDH0 Dishwasher - Instructions

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Following a utube video made it easy. Removed the outer cover of the door to expose latch. Two screws remove the latch, pay attention to how it was positioned and put the new one on and then replace the panel. But first turn off the electricity to the unit at the fuse box.

I removed and reinstalled the new gasket per the video instructions, but I found the corners to be much harder to install than indicated. I finally used a large, flat, dull screwdriver to carefully push the gasket all the way in, and used my fingers to feel whether the gasket was all the way in. I figured if the gasket wasn't all the way in, I would have a leak at the bottom of the door because the top of the gasket would stick out farther than the bottom, which is exactly what the original symptoms were. Perhaps I didn't need a new gasket? There was no visible damage. Pushing in the corners of the original gasket may have fixed it, but the new gasket worked perfectly! Thanks, Part Select!!

Watched video at parts select to remove front, stops, then for wheel assembly after fumbling with wheel assembly to figure where to put pressure on wheel assembly release catch .......reverse assemble.....
Finish. Relax and ponder how parts are designed to fail then easily replace- saving maint and service charges. Had machine 5 years and replace a different failed part once a year so far . Seems a fairly good system as long as parts available.

repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet

I was constantly seeing small bits of food blocking the spray holes in the upper and lower wash arms. After a bit of troubleshooting, thanks to the included schematic, the only possible thing left which could introduce particles was the under-unit disposal unit. The dishwasher had to be fully disconnected, removed, and tipped-over to access the pump and motor.

After removing the entire pump and motor assembly, it was obvious what the problem was - the filter screen (which is not accessible normally) was totally destroyed. The motor had ripped the mesh screen up, and sent shards of sharp metal throughout the unit. What a terrible design - a non-user-accessible filter which requires disassembly of the entire product to clean.

I replaced the entire pump and motor assembly which was pretty simple. Just use a very small amount of dish soap to lube the rubber o-ring up to make it slide into place easy. Reconnect all the cables in the same place you removed them from.

If you don't mind using some stainless hose clamps, you could maybe get away with replacing a lesser expensive subassembly - but for me it wasn't worth the hassle.

Pulled off old seal found center of new seal and pushed new seal into channel that old seal came out of starting at top middle underneath the latch

Followed the easy how-to video from PS. It was as easy as changing a light bulb.

watched video took less than 5 min to replace veeeery easy to do

put new hose on, very easy.

Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

I opened the package took out the replacement part and installed it with no tools. Easy, done in 10 minutes.

thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.