MDB4651AWW3 Maytag Dishwasher - Instructions

Removed assembly holding the docking station to insure the passageway was clear. I reversed the flappers and noticed an improvement in cleaning then decided to order a new part. Installation was simple and the repair seems to have worked well.

First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.

Accumulator was as easy as just removing srews and replacing the part. The Float I broke by accident and was more complicated to replace required 2 people to manage parts.
Dishes finally coming out clean!

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

Removed inner stainless steel shell of the door,revealing the broken latch/door handle. The old one fell out, and the new one snapped in. It was as easy as that!

Open door fully. Remove all screws that hold inside panel to Front panel. Carefully remove Inside panel being VERY CAREFULL not to pull wiring out of door switch [top of door] and operator switch panel [also top of door]. Remove door switch, next remove 3 screws holding switch panel in place. Remove the top plastic section where switch panel mounts and set aside. Carefully remove green ground wire from bottem hinge for door. [right side] Next CAREFULLY remove front panel from hinges using EXTREME CARE not to let hinges "free fall" to the open position. Remove old panel. Install new panel in the reverse order as the old one was removed. DO NOT PANIC if you happen to pull the "ribbon cable' out of panel switch. It will plug back in very quickly and only one way. Just make sure it is "seated" in plug. The "key word" for this panel replacement is CAREFULLY.

First, I turned off the power to the dishwasher at the main box. Then I removed the 10 screws holding the interior stainless steal cover to the door. I removed the broken handle and the broken piece from the door. I snapped the new handle in place and replaced the 10 screws before turning on the power.

This was the easiest repair job I've done and it saved me at least $100 dollars in labor.

Thanks to all who have submited their stories. Great help!

Removed the inside door panel. Had to borrow a friends power screwdriver with a star shaped bit to do this. Removed old latch and inserted new one catching the prongs so they could now lock and unlock by pulling up on the latch. rescrewed the inside door back and all was done.

I followed the directions in the dishwasher manual how to remove the top rack of the dishwasher, basically removing the stops on each side, and I set the rack on the counter. I replaced both sides even though one had not yet broken. To replace the part, 5 screws had to be removed; I used an allen wrench. The replacement location of the part was pretty obvious once the screws were removed. The inside of the plastic piece that was opened in the process of removing the defective part was dirty so I took some time to clean that out before attaching the new part. The actual unscrewing and attaching the new part probably took 10 or 15 minutes per side. It took a few tries to get the height adjusting lever to move freely before I tightened the screws. The rack works great now.

remove old seal, put in new - my 10 yr old could do it. Note - there is a white mark on the back of the seal indicating the middle so you can line it up when installing the new seal - makes it easier.

Basically took out of box and put in dishwasher.

Snapped out the old retainer, snapped in the new. Then snapped in the washer arm. Done. Works great.

Took the dishwaher apart. Found out the float was damaged. Replaced the float and the float switch. Put back together

Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.

I noticed that the dishes on the top rack were not getting clean. While the dishwasher was running, I opened the door to see if the arms were moving/spraying and they were not. I cleaned the filter and checked the impeller and both were clean and not damaged. After looking how the top rack slides into the "flapper" I took it off to inspect it. It was missing the rubber to make the seal with the tube from the top rack. After replacing this part, the dishwasher is cleaning like new. Here is the part PS2340934 Docking Station with Flappers