MAT10CSAAL Maytag Washer - Instructions

Determined that the lid switch was not completing the circuit. I then removed the 3 wires from their posts along with the 1 screw and removed the bad switch. Then, in reverse order installed the new switch. The part was 1/3rd the cost of the part sold locally. I ordered the part at 3:15pm Monday afternoon and it arrived at 1:00pm Tuesday- the next day. UNBELEIVABLE SERVICE....!

removed screws on front of washer, removed bolts holding top cover hinged back, nut driver to remove agitator, slipped agitator off, removed tub hoses, did not have special wrench to remove large nut on shaft, used punch and grinder to removed, had new large nut so wasn't concerned about damaging old one, pay attention to thread pattern to know how to turn, if you had special wrench job would be easier, removed spring bolts and took out inside drum and tub. cleaned corrosion and installed new seals, can be hard to slip on new seal, don't use grease, get dishwashing soap to use as lubricant to put on. Put back together and all is good.

After I replaced the timer, the washer still would not wash or spin. So my son replaced the lid check switch. It was hard to remove the screw, but he finally managed to remove it and easily replaced the switch. The washer works perfectly. We kept the timer installed (also easy to do by removing the old and replacing it with the new by just unplugging wires and I think one screw) because the old one had not worked properly for a few years when I had a similar problem which resolved, except it would only work in main cycle with soaking which was sufficient for me. This large capacity washer is in good shape and I hope will last at least another 5 - 10 years. ).

Took front panel off. Ran machine. Pump is see-through. Could not see any "aeration" of the water in the pump and no water was coming out of drain hose. Disconnected electric. Disconnected hose from drum to pump(first emptied ALL water from drom)and drained in bucket. Disconnected drain hose from pump to drain and drained any water. Checked for obstructions in hoses. Removed pump. Checked belt (was fine after 14 years). Ordered new pump. Received the next day! Replaced pump and tighten belt. Connected hoses and test it. All OK. Replace panel and did laundry.

Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.

Thinking the water pump was not doing its job in removing all of the water after the rinse cycle, I replaced the water pump.

1. Unplug washing machine.
2. Remove front cover (2 screws).
3. Pull belt and hoses off pump body (watch for water in drain hose!).
4. Remove 3 screws holding pump to bottom pan. 5. Reverse process with new pump.

This job is straighforward, and it helps to have 2 wood blocks to prop up the front of the washer.

Unfortunately, this didn't fix my problem. Actual cause of the water in the tub was a leaking inlet valve (solenoid assy).

followed instructions elsewhere here. Procedure went flawlessly
To undo the nut I used a 1 1/2 " long x 5/16 bolt to hammer on.

STILL LEAKS. Needed PS2347235 =Tub Bearing Kit . Going back in...
THe remainder concerns the bearing procedure:
The 3 bolts holding the outer tub to the legs have rectangular washers. Those are not totally flat, and are marked for outside, top ... so pay attention. It might make a difference.
Outer tub came off the rubber bushing. Took some pulling the bushing off the shaft, and removing the sleeve bearing was a challenge at first, it would not move on the transmission shaft. Soaked with wd40 overnight. Drove it off with cold chisel (driving upward). For re-attaching the 3 tub bolts I used a ratchet tiedown strap to pull the 3 legs together to get enough thread to start, what with all those washers and things.
Ran spin cycle dry for 3 minutes as per instructions before filling with water. Success.

I looked at the common problems in the owners manual and one item was the lid was not closed or the lid switch was bad. I took off the control panel and there was a schematic inside. This showed 2 lid switches. When trying to see if one switch was closed as it should be, touching the multimeter to the contacts was enough to get the washer going. .

checked lid switch ,plunger stuck in the in position 1 amp fuse blown took switch apart it was full of green copper corrosion stopping plunger from moving correctly. replaced switch and fuse and wow washer works

Removed control faceplate (2 screws on top edge and flip forward). Removed wires one-by-one with needle-nose pliers and replaced on new switch to avoid mixing the connections. Removed screw and replaced switch then, replaced screw. Moderately tightened new part and operated lid. Listened for click open and closed. Adjusted switch position for proper "click". Tightened screw and replaced front panel. Done in about 10 minutes.

Opened top - removed old switch assembly. Plugged in new switch and re-assembled. Had to reopen top when washer filled and did not start cycle. Switch assembly needed moved slightly in order to engage second switch.

I removed the old lid switch assembly from washer and one by one exchanged the wires to replace correctly on the new part. I placed the new lid switch assembly in the washer using the screw to tighten the part in place. I turned on the washer and after the water level stop the wash cycle began immediately. Friends were impressed I used your web site to determine the part selection by the previous reviews and that I replaced the part with ease. Thank you for an user friendly web site.

Granville County/North Carolina
6/13/2010

It was fairly easy, start out by using a screwdriver and push down and out on the front cover and remove it. Take out the 2 small bolts that hold the top cover down to the sides and lift the top cover up and lean it back out of your way. On the bottom side of the agitator there is a small bolt that holds it down, loosen that bolt and pull the agitator out. The hardest part of the entire jod was to use a small chisel and hammer to take off the nut that holds the assembly down.Remember it has reverse threads,you have to use a chisel to back it off and use some WD40 to help remove the calsium build up that is around it. Once you get that large nut off, there is a set screw on the side of the assembly that you have to loosen up before you can take it off, it's a "star driver" head and not a allen wrench set screw.Just take your time and look at your new part and compare it with the old one and take your time and remember how you take the old part off,and you will not have any problem putting the new one on. This was the first time I ever worked on a washing machine, and by checking out the parts first and comparing everything,even someone that might not have much mechanical skills can change this out. My washer works fine and not a drop of water leaks anymore.One thing I did learn, if you change this part out and put it back together and try it out and it makes a funny sound and you smell something like its burning, you might did what I did. I thought I had it to tight, but I put the large nut on before I put the tub back on!!! The agitator was holding the tub down, but it could not spin in spin cycle.... Good luck with you repairs, you can do it.

Removed top. Removed agitator and tubs . Replaced seals and reassembled.

Remove front panel. Then remove top of washer, two bolts at front of top. Then remove two bolts that hold switch assembly to top on right side of top. Switch gets pried out. It just sits in with small pins holding it in place. Wire connectors hold very tight. Install is reverse.