MAH14PDAAQ Maytag Washer - Instructions

after cutting my hand I installed masking tape around the opening on the back of the washer. All went well after that

Repair went just as video on this website indicated. Reinstalling the cable clamp was the hardest part.

Using the video tape (YouTube URL) provided, I went step by step and replaced the bellows with no problem. No water leaking..the toughest part was putting the spring back on, it takes some coordination and muscle.

I followed the instruction of using a tie strap to secure belt to drive pulley and turn pulley to place belt on pulley. Worked great. Done in no time.

Working from back of machine, slip old belt off drum pulley. Loosen 1/2" nut to remove drive motor from outer drum assembly. Work motor toward front of machine, while holding carefully, to slip out of old isolators. Remove worn isolators. Replace with new isolators (lip towards front of machine). Re-install motor with the nut/washer all the way up against the stop for the least amount of pressure possible on belt tension..tighten bolt. (Believe me.. when you try to install the belt, it will still seem like the belt is not the right size and way too tight.).. It is, however, the correct belt.
Have a zip-tie ready.
Engage the new belt on the motor shaft pulley. The belt grooves should line up with the motor shaft grooves towards the end of the shaft. Grip the drum pulley and rotate counterclockwise while guiding the belt onto the pulley. At about 12 O'Clock, zip-tie the belt to the pulley.. then rotate ccw until installed.. (about 6 O'Clock). Snip off the zip-tie and your ready to go.

I followed the steps on the first post which are very good. I had trouble, however, putting the seal over the drum. I finally removed the plastic rim to the drum by removing the clips. I was then able to lay the rim on the floor and put the new seal over it more easily. It is a lot like putting a bicycle tire on a rim. I had no helpers so I used a vice grip pliers on one end of the cable-spring and another pliers on the other. I was then able to pull both ends together enough to get them to hook up. I recommend removing the plastic rim as I mention above. Had I done this first, I would have done the job in less than 30 minutes.

We followed the directions in other people's repair stories here. Removing the spring was a challenge, as was getting it back on! The rest of the repair was simple. Be patient with removing the soap dispenser. Ours had some plastic cords connecting it to the frame which we didn't anticipate, and we broke them because we didn't see them.

We're going to try that new Affresh product in the hopes of avoiding this repair again in the future. We never washed anything harmful in the washer. This seal becomes moldy and deteriorates with time. Using bleach to kill the mold only speeds the process.

Even though after reading many repair blogs saying not to remove the back of the washer, I did anyway. Lo and behold after opening it, the pump was right there!! I removed the hoses (make sure you have a bucket, or shop vac handy) lots of water will come pouring out use your bucket for this, I used my shopvac to suck the rest of the water out of the hose, and bing, the washing maching door opened and allowed my to retrieve my clothing(stinky now after the washing machine held them hostage for days) I removed it by removing 3 bolts, and 1 screw very easy. I took apart the pump to see if there was anything blocking up the moter there was nothing, but the plastic pump blade was chewed up so bad, it no longer would turn to pump out the water. I had to order a pump. When my pump came in 2 short days later, I reversed to removal process and presto!! The washing machine was running like new.

I removed the back panel and located on the left side of the washer removed the pump and replaced it.

Removed back of washer and unscrewed pump band and hose removed pump and replaced pump,replaced hose to new pump,WE really appreciated the fast shipping of the part from your facility.Thank You again

Unscrew door hinges, front panel, soap tray, lift top to 12 oclock position,unhook strap from spring located on top of the drum,tape strap ends to drum to prevent from falling,disconnect the billows drain clamp on the bottom of the billows,remove the billows by peeling off the drum, install the new billows from the top first and tape it to the drum to prevent it from slipping off as you work your way around the drum,install the strap in its track, secure with spring(better with two people)in same location, hook up billow drain, finish doing the laundry.

I removed top control panel and then the old power cord that been damaged by a small fire and the just attached the new power cord and control panel. Unblievably simple and I saved myself a lot of money. Where I live in a NYC suburb this type of simple repair could easily cost $100.

The motor isolators went in with no problem ,but the drive belt went on very tight , your how to video shows how. Easy the belt went on , when I called your store I was told that is the only size belt for the machine model mah5500bww,
Thank you Bill

Received 2 seals with seal kit and didn't know which seal went where and online it was stated in a video the kit included a "revised" seal but couldn't find anymore information than that. Installed what I thought was the seal to be installed on the inner seal. Did not have any information on the depth of the bearings installation on outer or inner bearing set depth. Tried to call help line but never got through. I think it is installed right? Guess I will wait and see how the drum holds up and hope the bearings and seal are installed correctly.

I looked on Utube at some videos which helped a lot all told i replaced the bearings in the outer hub which was quite a chore as the bearings came out rather hard I used a steel rod about 18 inches long and a heavy hammer to pound the old bearings out they came out hard then I put the new bearings in very carefully as I had to tap them back into place and installed the seal and put the new shaft on the tub and slid everything back into place. The instructions that came with the new seal and shaft were very helpful I bought the new bearings from local implement dealer as they were not available with the shaft and seal didn't keep track of my hours probably about 21/2 to 3 hours