MAC1200 (Type 1) DeVilbiss Compressor - Parts

This is a genuine replacement part manufactured for use with outdoor power equipment and air compressors. This nut is used to fasten various part assemblies on a range of different products. This nut is sold individually, please see model diagram for part usage and location.

This replacement screw is a genuine OEM sourced item commonly utilized on air compressors and pressure washers. It is a standard hardware which has multiple applications depending on the unit. Please make sure to check diagrams of your model for the correct location and used of this screw. This part is made from durable metal and it is sold individually. You will need a wrench to install or remove this hardware.

This rod kit is an original part from Craftsman for air compressors. This part attaches to the piston to the crankshaft that is in the pump. This kit includes the following: cylinder head, piston, cylinder head gasket and piston ring. You will need a wrench set and socket set to replace this part. When installing this part, it is recommen...Read moreded that that you fasten the top screw (50-60 inch- pounds). This kit is made of metal and rubber.

This replacement valve plate assembly is a high quality item designed for use on Craftsman air compressors. It is a genuine manufacturer sourced item that is used to control the airflow into the cylinder. Once the piston starts traveling up, the reeds on the valve plate open and air is sent into the air tank. Overtime the reeds will get w...Read moreorn eventually requiring valve plate replacement. One metal valve plate with reed valves and two rubber seals are included in this assembly. When replacing this valve plate assembly it is also a good time to replace the head gaskets which are sold separately. You will need a wrench set to complete this repair.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is an authentic Porter Cable replacement part, sourced from the original manufacturer for use with air compressors. The special tray tool is commonly used to store pneumatic tools and to cover the motor shroud. This tool tray is available as an individual replacement part, please see model diagram for associative parts.

This is an authentic Porter Cable replacement part for air compressors. The shroud bracket is used to attach to the rear shroud and act as an anchor point for the front shroud. The bracket is made of high-quality metal. This item is sold individually.

It is an OEM component which is designed for use with air compressors. This special nut sleeve assembly secures the pressure relief tube to the pressure switch. It is a high-quality replacement for a damaged or a missing hardware that was installed on a new unit. One durable metal nut sleeve assembly is included. A wrench will be needed t...Read moreo perform this repair. Check the appropriate diagrams for your model to ensure the proper replacement procedure. Make sure to drain the air before starting this repair.

This is an authentic replacement part manufactured for use with Porter Cable air compressors. The safety valve is used to prevent the tank from overpressurizing by letting air out of the tank when a specific pressure is met. Safety valves have specific pressure tolerances specific to the model of air compressor it is important to match th...Read moree valve to your model of compressor. This safety valve is available as an individual replacement part.