MA1302W LG - Instructions

I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations ... Read more on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.

Initial failure of over range microwave Aug 3rd. Control Panel worked but no heat. Took to local LG authoriaed local repair place. They fixed it quickly and we re-installed it. Worked fine for 2 months then had similar failure again. Agaim took to same authorized repairer. They kept unit for 3 months but finally concluded theu could not ... Read more fix it and suggested we contact LG for a partial refund. When they tested the unit during re-assembly in my presence, there was a blue flash and the fuse blew. Since we had built a custom tile mural back splash around this unit, I brought it home, ordered a number of time delay fuses new capacitor and two new high voltage diodes. However, using my Fluke DMM, I checked the existing capacitor and high voltage diode and they checked OK so I just replaced the time delay fuse. The high voltage transformer leads had 2 possible ways to connect to capacitor and diode. Tried one way, plugged unit in and turned it on, and immediatly blew the fuse. Replaced the fuse and reversed the high voltage transformer connections,amd turned unit pn, and it worked perfectly. Since we had experienced several power failures during the time of the original failure, the repairer concluded that power spikes might be at fault, so I also purchased a TrippLite ISOBAR4ULTRA 3300 Joule surge protector between wall outlet and microwave, and re-installed over range. It has worked perfectly since.

unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .

You have to remove the cover which in my case was a little more difficult because the unit is wall mounted and has a frame around it. That was the hard part. Once the mounting frame was removed, you can remove the cover and the light bulb is on the top right side of the unit. One screw removes it and the new one pops right in. Put the cas ... Read more e back on reinstall it in the wall and voila...piece of cake.

you will a security socket T20. this unit was installed over oven, remove trim cover,remove screws holding unit in place,I used a helper to get the unit out, once out you have to remove all the screws holding the cover on,on two of the corners they use a security hex screw so you need a special socket for that. remove the door latch switc ... Read more h,take your time or you will break tab holding switch in. ask me how I know.but super glued broke piece in place and plugged wire back in.the new latch may have a second pin but look at old one and plug wires in the same way.the light bulb does not screw out so I had to purchase the entire unit.total cost under a $100.00 to do repair.

"PIECE OF CAKE" Removed cover,removrd bulb, replaced bulb, replaced cover. "PIECE OF CAKE" P.S. Wife is happy.

Partselect sent me the right thing in two days! The whole process was easy as pie.

We got a a carbon steel but and drilled out the stews and put in regular screws. We also had trouble getting the cover back on and ended putting 2 more screws on the left side which had none. The installation was the easiest part of the installation.