LSFS213ST (ASTCNA1) LG Refrigerator - Instructions

I watched a couple of You Tube videos on how to make the repair, ordered a new spring from Part Select, and installed the new spring when it arrived. Took about 5 minutes for the actual repair.

Check the spring when it arrives. The first one I received was wound the wrong direction. Called customer service and they were supe ... Read more r. Refunded the charge for the first spring, found the correct one for me, and mailed it out.

Pulled the old gaskets from the doors and then inserted the new gaskets into the slots. The gaskets are easy to remove. Just a firm pull and you're on your way to the repair.
Just make sure the gaskets are seated all the way around the doors. You'll be surprised how nice the doors close with the new gaskets in place.

This repair is pretty straight forward. Just remove the 3 screws that hold the ice maker and bin assembly in, unplug the wire harness connector, then remove it from the refrigerator door. Once removed you simply need to remove 3 more screws that hold the ice maker to the auger/bin frame, remove the temp sensor, and a couple pieces of ta ... Read more pe. Re-assemble the new ice maker in reverse order and you are all set. I think part of the issue I was having was due to mineral buildup in the tray as well so it had a hard time cracking and removing the ice. Not sure why it was overfilling, maybe the sensor was broken or had buildup on it as well. This solved all the problems I was seeing and now it makes great ice that doesn't stick together and form a bridge in the bin.

Swapped old one with new one. New one had extra plug not needed.

Followed instructions online

Unable to complete repair due to lack of response to emailed question concerning another spring. No picture of spring in question on website making it impossible to be sure of comparability without clarification. Unable to call currently due to no in person support. Just stuck now without an answer. Frustrating to say the least.

Remove 2 screws swing light down a little bit and pull it to front unplug wires . The hard part of job was finding new replacement light, Partselect.com was only sight I could find that had new replacement number and had the light . Other sites including LG site would only tell me the part number on old lights was discontinued 2 of sites ... Read more said try used appliance dealers

Watched tube video about the repair
Ordered part
Performed repair as per the video

Watched the video. Took the screws out, unplugged the connection and slid mullion off. Then plugged the new one in, slid it on and attached the two screws.

Pulled old gasket off by hand. New gasket was easy to install by pushing it into molded cutout in refrigerator door.
Very satisfying to have no glitches in the seamless installation.

1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs o ... Read more n the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!

Just like on YouTube very easy to do

The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.

Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...

Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.

Super SImple/