All Installation Instructions for LG Refrigerator LRFD25850WW

The tray cover broke, the drawer guide broke

The repair was easy peasy! Just fit it all in. Shopping here was just as easy. I'd delayed doing it for so long because I thought it'd be laborious but I found my appliance fast and the parts I needed quickly. The diagram you provided with part numbers helped a lot. Thanks for making it easy.

Parts Used:

Drawer Guide

Tray Cover

Kathy from Boise, ID
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Interior Light Would Not Turn Off

Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.

Parts Used:

SOCKET,LAMP

Thomas from Bay Shore, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Broken plastic drawer and crisper front

1. Removed old, broken parts 2. Insert new ones

Parts Used:

BUCKET ASSEMBLY,ICE

Crisper Drawer Front

William from Burlington, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Tray Cover was broken where it attaches to the refrig. This is the Third one in 6 years

The plastic is real weak and the articulation point is not manufactured strong. You have to put one end in a female receiver and flex the tray cover with your fingers crossed hoping it won't snap, while sliding the other side into a similar female receiver on the other side. The Crisper drawer front has not come in yet. Disappointed that you have to buy the entire drawer with a front instead of the front. This is the 2nd one I have replaced. The difference in the Drawer Front...$10.00 and then entire Front and Drawer, $45 plus...

Parts Used:

Tray Cover

Crisper Drawer Front

Phillip from knoxville, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

not a problem

snap it on!

Parts Used:

Crisper Drawer Front

LORI from INDIANAPOLIS, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Lamp cover and case had melted

I removed the old lamp cover and case. Discovered that the last repair person had not re installed it correctly so the case had melted from the bulbs. I Removed the screws that was supposed to hold it up, assembled the case and cover, inserted the screws and anchored them in where they belong. Problem solved!

Parts Used:

Lamp Cover

Refrigerator Lamp Case

Donna from Abilene, TX
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Crisper Drawer broke on right hinge

Replacement part from PartSelect was OEM, identical to original part. Installation was very quick. Inserted hinge on left side and then depressed the right side to slip it into place. Presto, it was done. Most impressed with PartSelect on the OEM replacement part and very prompt delivery.

Parts Used:

Crisper Drawer Front

Kevin from Reno, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

door mounted cold water tank was leaking at seam of polyethylene tank.

The part labeled as water tank was not pictured on web site, and when it arrived it was a large coil of plastic tubing wire-tied in an oval shape,not a blown p/e tank as original.The oval of tubing would not fit into the door compartment, because of the bulk of the actuating solenoid. No instructions were included. It was necessary to hacksaw the steel solenoid mounting bracket off the solenoid, then contort the solenoid into the compartment to get all parts inside the cover. new connectors had to be purchased, because the the tank/tubing coil was 1/4" od, while the original tank had 5/16"od connections.

Parts Used:

Water Tube

RONALD from LAKE WALES, FL
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

Was this instruction helpful to you?

broken shelf frame

Removed two drawers and drawer covers, glass shelf and door frame. Replaced in reverse order.

Parts Used:

Lower Shelf Frame - White

Robert from Hackettstown, NJ
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

Was this instruction helpful to you?

broken part

replace piece

Parts Used:

Tray Cover

Lisa from Santa Fe, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Broke the crisper drawer front

While cleaning out the frig we removed the bottom shelf to remove the glass and really scrub it down. When we went to put it back in, my wife grabbed the crisper door front and snapped it offf. I immediately went to the computer to find a replacement part and found PartSelect.com. I plugged in the model number and I immediately saw a diagram to pick out my part. I had it ordered before she got all the food back in the frig! The part arrived early and I installed it in a matter of seconds. So easy to find the part, order it and install. You have a new customer!!!

Parts Used:

Crisper Drawer Front

Johnny from Acworth, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

The drawers were sagging on one side due to broken plastic tabs

I replaced the entire plastic frame to fix the drawers. I'm frustrated that the design requires that I do this. Removed the metal bar that actually provides the support for the front of the frame and the drawers, etc. Three screws to remove and re-install. Easy. After removing the drawers, I just gently bent the drawer cover hinges to slide them out of the frame and tilted the frame out of the fridge. The glass just came out easily as it's not attached with any clips. I had to work to remove the clear plastic panels but a little careful persuasion and I was able to white supports out of the way and remove the panels. Then I removed the aforementioned bar and replaced the glass re-installed the whole assembly.

Parts Used:

Lower Shelf Frame - White