LRFC22750SW (ASWCLGY) LG Refrigerator - Instructions

Unscrewed what remained from broken door stop, aligned new one, screwed it in. Done!

1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!

Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.

Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE

Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape

I just popped in the new cover lamp. It took less than 5 mins. if that much.

I turned off the water supply. Took off the access panel at the bottom of the fridge. Disconnected the waterlines from the valve. Remove the screw hole in the valve in place install the waterlines on the new valve attach the new valve to the refrigerator, reinstalled the back panel turn on the water And it made ice.

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)

Pulled the fridge out of its space. Removed a metal shield which covered the bottom 12" of the fridge with a Philips head screw driver. The water valve is on your right. turned off the water to the supply line. Removed the supply line using an adjustable wrench. Removed the water line gong from the pump into the fridge. It is held on with a "C" clip which can be pulled off with needle-nose pliers. Removed the old pump, held with one Philips head screw. Then installed the new pump, reconnected the lines, replaced the metal shield and turned the water back on. Vacuumed the fridge and its space before cleaning up. The ice-maker now works perfectly.

Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.

I removed the cover from the rear of the unit, with a screwdriver. Then with a adjustable wrench unscrewed the top nut of the water valve.I then removed the screw holding the valve to the wall of the fridge. Turned the valve upside down and removed the line going up to the ice maker. No tools needed here as it is a quick connect fitting.Use reverse order to install valve.I am 65 years old and if I can do this anyone can. Good luck from TX.

I was told the mother board went out. Took a few months to finally get one myself after repairman didn't come through. It turned out not to be the motherboard that sears repairman tested it for and said that's what it needed. I found Parts select after going round and round with sears parts refusing to accept return. There prices were better, as well as shipping and it came so quick i thought it was over night. The controller assembly was not the problem so we have it for a spare now. It was the freezer fan but even after installing it nothing would work is why we ordered the controller assembly. after 2 days and about 7 hours of checking, taking apart, rechecking assembling by my determined electrician it turned out to be a loose wire. LOL hope this helps someone. I'm just glad to have my fridge again! Blessings!!!

slid screw driver under edge of switch, easy.