1. Home
  2. LMX25986ST
  3. Instructions

LMX25986ST (ASTCNA0) LG Refrigerator - Instructions

All Instructions for the LMX25986ST
61 - 75 of 94

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The plastic cover on the butter area had broken.
1 person found this instruction helpful.
  • Elizabeth from TALLAHASSEE, FL
  • Really Easy
  • Less than 15 mins
Just had to slip the 2 pegs into the existing holes.
Was this helpful?
Thank you for voting!
Door light switch, 3rd one I have replaced in 6 years made in China.
1 person found this instruction helpful.
  • Charles from CURWENSVILLE, PA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this helpful?
Thank you for voting!
Removed old part.
1 person found this instruction helpful.
  • Steve from NORTH AURORA, IL
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Installed new one.
Was this helpful?
Thank you for voting!
Light quit coming on when door opened.
1 person found this instruction helpful.
  • Calvin from Northome, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Was this helpful?
Thank you for voting!
Lights didn't come on when door was opened
1 person found this instruction helpful.
  • Philip from Ashland, MA
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this helpful?
Thank you for voting!
INTERIOR DOOR ACTIVATED LIGHT SWITCH QUIT WORKING
1 person found this instruction helpful.
  • JON from OJAI, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs o n the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!
Read less
Was this helpful?
Thank you for voting!
Slow water for drinking
2 of 4 people found this instruction helpful.
  • Steven from SEBASTIAN, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
Just like on YouTube very easy to do
Was this helpful?
Thank you for voting!
bad switch
1 person found this instruction helpful.
  • Michael from TONAWANDA, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this helpful?
Thank you for voting!
The switch became intermittent - Possibly a poor designe
1 person found this instruction helpful.
  • Sidney from ENDICOTT, NY
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
Was this helpful?
Thank you for voting!
rail that holds meat tray broken
1 person found this instruction helpful.
  • Steve from GEORGE WEST, TX
  • Very Easy
  • Less than 15 mins
  • Screw drivers
remove all trays from refrigerator , remove screw holding rail and install new rail.
Was this helpful?
Thank you for voting!
Spring in the plate front assembly broke. Door plate assembly would not move into correct position, preventing door from closing.
1 person found this instruction helpful.
  • Robert from WARREN, RI
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Followed Youtube video provided on the PartsSelect Website:

https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST

Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.
Was this helpful?
Thank you for voting!
Replace switch
1 person found this instruction helpful.
  • Dean from HILLSDALE, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Was this helpful?
Thank you for voting!
door slight switch failed
1 person found this instruction helpful.
  • Greg from CASA GRANDE, AZ
  • Really Easy
  • Less than 15 mins
  • Pliers
Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.
Was this helpful?
Thank you for voting!
Spring broken in door mullion
1 person found this instruction helpful.
  • Wayde from SEMINOLE, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took 2 screws out and disconnect wire and install new part.
Was this helpful?
Thank you for voting!
Butter bin door had broken
1 person found this instruction helpful.
  • Mary from DEL MAR, CA
  • Really Easy
  • Less than 15 mins
Simple replace of door, fits perfectly
Was this helpful?
Thank you for voting!
All Instructions for the LMX25986ST
61 - 75 of 94