LMV1683ST ((CS1ELGA)) LG Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
turntable wobbled
removed power cord replace turntable motor by lowering bottom panel removing two screws holding the motor on and two wires and reinstalled
Parts Used:
-
James from Rantoul, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
blew fuse
tested cap. with ohm meter which showed a short. A new HV cap., a fuse and it is working fine again.
Parts Used:
-
larry from LUCERNE, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The new part was too thick for the worn out plastic ring which is obsolete.
Needed to raise the part to match the ring. I used peanut butter to hold plastic shim while replacing to hold it in place. Built in Oct. 2009.
Parts Used:
-
James from PURCELLVILLE, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grille assembly broke off
Use a ladder.
Remove the broken part if it’s not already off.
Remove and save the screws from the top of the microwave.
Unwrap assembly and insert it into the gap aligning the points.
Screw the screws in.
Verify fit.
Done!
Remove the broken part if it’s not already off.
Remove and save the screws from the top of the microwave.
Unwrap assembly and insert it into the gap aligning the points.
Screw the screws in.
Verify fit.
Done!
Parts Used:
-
Dee from MOKENA, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old ones broken
-
DIANE from PORT ORANGE, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Change the Charcoal Filter and Microwave Grease Filter (Normal Maintenance)
Both were easy to replace. I followed the instructions in the users manual which came with the microwave. On the grease filter, I removed the 2 Phillips head screws which hold the grill plate in place. I had to open the microwave all the way to remove the grill plate. The grease filter was easy to remove and replace with a new one. I then put the grill back in and secured it with the 2 screws. Easy Peasy!
Parts Used:
-
Lynwood from GONZALES, LA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace resin cover in microwave
Used fingers to pull damaged cover away from microwave interior body. Used fingers to snap replacement cover into open slots.
Cover snap right into special slots.
Cover snap right into special slots.
Parts Used:
-
Paul from MCMINNVILLE, OR
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Shaft socket was worn out
-
Cesar from Miami, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Latch spring keeper broke
Removed door from microwave and then popped the inside widow trim ring off. Removed 4 screws from the window bracket, replaced the latch with a new part and then assembled.
Parts Used:
-
Gregg J. from WEST CHESTER, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb replacement
-
Marianne from CHURCH HILL, MD
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
8 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave operated but did not heat
Initial failure of over range microwave Aug 3rd. Control Panel worked but no heat. Took to local LG authoriaed local repair place. They fixed it quickly and we re-installed it. Worked fine for 2 months then had similar failure again. Agaim took to same authorized repairer. They kept unit for 3 months but finally concluded theu could not fix it and suggested we contact LG for a partial refund. When they tested the unit during re-assembly in my presence, there was a blue flash and the fuse blew. Since we had built a custom tile mural back splash around this unit, I brought it home, ordered a number of time delay fuses new capacitor and two new high voltage diodes. However, using my Fluke DMM, I checked the existing capacitor and high voltage diode and they checked OK so I just replaced the time delay fuse. The high voltage transformer leads had 2 possible ways to connect to capacitor and diode. Tried one way, plugged unit in and turned it on, and immediatly blew the fuse. Replaced the fuse and reversed the high voltage transformer connections,amd turned unit pn, and it worked perfectly. Since we had experienced several power failures during the time of the original failure, the repairer concluded that power spikes might be at fault, so I also purchased a TrippLite ISOBAR4ULTRA 3300 Joule surge protector between wall outlet and microwave, and re-installed over range. It has worked perfectly since.
Parts Used:
-
Donald from Oak Ridge, TN
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
1 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
turn table motor
remove the screws from the bottom, leave tthe light wires attached. There are two screws holding the motor on, disconnect and mark the old unit where the yellow wire goes. Mount motor with two screws and connect wires. Turn on Miicrowave for 10 sec, to be sure all is correct. Attacch bottom cover and reattach power cord. Before doing anything make sure power cord is disconnected and reattached when sealed.
Parts Used:
-
Gary from Desert Hot Springs, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No Heat
1. Removed unit from the cabinet. (2 screws). 2. Remove the outer microwave metal shell. (10 screws). 3. Locate and remove part. (3 screws). 4. Install new part and replace all screws. 5. Install unit back into cabinet. So easy. I will share this site with all of my friends.
Parts Used:
-
Dennis from Chesapeake, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken Tray ,Glass
Received my replacement Tray,Glass in only 2 days. Opened it and placed it in the Microwave. Yep, it was that easy!
Parts Used:
-
Gena from ROSICLARE, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Light bulb burned out
I unscrewed the light cover, removed the burned out light bulb and replaced it with one I ordered on Partselect.com. It was very easy.
Parts Used:
-
Craig from Burke, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!