LGEF3045KFE Frigidaire Range - Instructions

Unplugged unit and removed back panel with nut driver. Removed door, racks and unscrewed element braces from back of unit. Removed element and installed the new one. Reversed the process and then ran the unit through a preheat cycle to test it.

My husband followed the video instructions and it was easy to fix.

Twisted replacement bulb into place easily. Let there be light!

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

The light apparatus was loose behind the panel. Remove the remaining part of the lens. Install the new lens from the outside of the panel and hold it in position, protruding into the inside of the panel. Slide the light apparatus onto the lens from the inside, allowing the bracket to hold it in place - it will be spring loaded, which will ... Read more hold it in place.

Open oven door completely. Release hinge locks by prying top of tabs at hinge. Close door halfway, lift stright up about 1/2", and away at 45 degree angle to remove entire door from hinges. Set door on blanket on floor with front facing down. With Phillips screwdriver, remove top two screws holding handle. Set handle aside. At bott ... Read more om edge, remove four Phillip's screws. You can now separate the outer door shell from the inner door. Clean out any remaining glass. Tip: This is a great time to clean inner glass of any grease or other liquid that may have gotten between the glasses. Set new glass in place with foil at top facing up and slide fully to the bottom of the outer door. Reattach the inner door to the outer shell with the four bottom screws and the top two handle screws. Tip: Get handle screws started, but do not tighten until all four bottom screws are started. Snug but do not overtighten. That's all there is to it. Re-insert door hinges into slots on oven frame and push down to seat. Engage hinge locks and close door slowly to make sure hinges are seated properly. My wife did this by herself in less than 30 minutes while I walked her through it.

removed the old burner and put the new one in it's place.

The light and sensor were straight forward and easy. The EOC was as well but there was one glitch. You have to also purchase the black panel overlay, you cannot use the old one. While the adhesive will still adhere, the keypad is different and REQUIRES the new cover. This would have been good to know when I ordered parts as I did not ... Read more know until I got the three parts and had to reorder the overlay creating a weeks delay in it's repair.

When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced th ... Read more e back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

moved the range out to access back
removed 5 screws from back panel
removed 1 screw from thermostat installed new one
replaced screws, done in 20 minutes
problem solved

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in ... Read more the house.....I show them what I DID!! :-)

first the temperature sensor then the igniter. started to do the igniter by using common sense then I used YouTube which made it a lot faster.
the temperature sensor installs from the back of the stove, the igniter installs from thr front ie, the drawer and inside oven.

Followed the parts select video. However there were differences. Four screws to release stovetop from brackets very difficult to break free even once correct bit identified. No spring clips but studded screw and coil springs let elements fall right off underside bracket. Need fours hands to hold back in place to screw bracket back in plac ... Read more e to hold elements.