LFX28968ST ((ASTCNA2)) LG Refrigerator - Instructions

Read the reviews from other members and just did as they said. Needed a screw driver and the info from past persons review couldn’t have been easier.

The glass was ordered correctly. The part was too big for mt refrigerator. I tried to send it back, but I got no reply. I tried cutting the glass to size and it shattered. I wasted 60.00 and im disgusted with your company.

Swapped old one with new one. New one had extra plug not needed.

Took the old one out and put the new one in.

Replaced drawer.

Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...

was easy watching youtube video of how to replace whole ice maker, was only 3 screws, remove from the door, a couple of screws hold it to the flat piece, route the wires around the unit, connect the plug as installing it in the door, position it, and tighten 3 screws, that easy

I am a73 year old woman. If I can do this, anyone can. Super easy. Just watch the online video.

REMOVED 4 SCREWS HOLDING UNIT IT DISCONECTED PLUG TO CONTROLER AND REMOVED IT BY PULLING OUT ON THE BOTTOM FIRST. TO INSTALL SLIDE THE UNIT UP AND IN FROM THE BOTTOM CONNECT THE PLUG AND INSTALL THE SCREWS. THE TOP SCREW HAS A PLASTIC SPACER WASHER. UNIT WILL NOT START TO MAKE ICE UNTILL IT REACHES TEMPATURE, GIVE IT TIME. WATER DESPENSER WILL WORK. CONTROLS ON THE FRONT OF THE DOOR WILL LIGHT UP NORMALY. I REMOVED MINE WHILE WAITING FOR PART TO ARRIVE, 4 DAYS. EVERYTHING WORKED EXCEPT WATER & ICE DESPENSER AND CONTROL DISPLAY ON THE DOOR.

Removed mullion strip with Phillips screwdriver replaced spring reinstalled the mullion strip all in about 15 minutes.

Followed Youtube video provided on the PartsSelect Website:

https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST

Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.

Removed old bucket and placed new one In its place. New one is actually better than OEM part because it has an arm than breaks up any ice that may jam.

The spring broke on the flapper (mullion) on my refrigerator. I sent a chat message to PartsSelect (they answered right away) to see if they had a replacement spring but it was not available so had to order the whole mullion. They gave me the part # I would have to order. It arrived quickly. The new mullion didn’t have a visible spring but it worked the same if not better. I just had to remove 2 screws on the center plate on the existing mullion, pull the plate out enough so you will be able to slide the mullion (the wires are under the plate kind of like the ones you see on a ceiling smoke detector) but you can’t get under the plate until you release the mullion. Push up on the mullion so that the plastic tabs on the top and bottom are released. Once the mullion is released (you have to hold it), you’ll see the wires. Unhook the wire part by just pushing down on the little tab and remove it. To install the new one, just reverse the steps. Align the top and bottom plastic tabs to fit into the slots, just enough to hold it in place. If the plastic tabs are not already flipped out, you’ll have to just flip them out. The top tab does not have tension but the bottom tab has tension so just push on it with your finger to flip it out. The plate covering the electrical is a rather tight fit and you have to make sure the little tab on the inside of the plate is above and behind the tab on the inside where the wires are so it slides behind it so you can get it in position before sliding the mullion back down into place and the electrical plate is in place too. Then screw the 2 screws back in. The hardest part is holding the mullion while un-attaching the electrical and just make sure you stuff the wires in enough so you can get the plate back in position. I’m a 75 yr old woman and managed fine by myself. At first when installing the new one, I couldn’t slide the mullion down enough to get the electrical plate in position and then realized I had to have the little tab inside the electrical plate behind the tab inside the wire compartment so they didn’t hit one another when pushing the mullion back down. Then, all went fine.

Just laid the shelf down. Fit like a glove!

Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.

Super SImple/