LFX25991ST00 LG Refrigerator - Instructions

I suggest turning off the water valve and power to the refrig before starting work. If this is not done the water dispenser will probably spray water down the front of the refrig. The whole icemaker assembly must be pulled out from the front. It is a friction fit--just insert fingers in the ice chute and pull out. The entire piece will pull out from the door. The control panel cover is held in by 8 screws that extend through the circuit board to the cover. It is a good idea to unplug the wiring to the circuit board when replacing the cover to prevent tension damage to the small guage wires. Once the new control panel cover is attached to the circuit board, the whole assembly can be reinstalled into the door.

Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.

Before you begin, I'd recommend unplugging the refrigerator. You have to slip the putty knife in around the edge of the dispenser panel and carefully release the tabs all the way around and the entire panel pulls straight out. There are three wiring harnesses to unplug. You'll have to remove several screws and release the tabs around the electronic panel and remove it from the main panel. It's a good idea to take note or even pictures of how the ice and water actuators are positioned on the panel, so you get them situated properly on the new panel. If the ice actuator is not fit correctly on a knob that sticks up it may dispense ice all the time (happened to me). After you transfer the actuators to the new panel and the ice and water dispensing levers, you can re-attach the electronic panel on the left side. make sure all of the wiring harnesses are plugged in and the wires situated out of the way, then re-install the panel by pushing it straight back in. Plug the refrigerator in and test it out.

I installed the new 3 wire ice maker very easily, but it was defective. I was told that instructions for the return of the defective part would be sent later due to the virus. I have never received the return instruction.
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return instructions if y’all still want it back.
Thanks,
Thomas Pennebaker

Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.

I actually watched a YouTube video for LG refrigerators. The hardest part was taking the wire harness out. Mine was really stuck in there. But got it, put the new switch in and viola it worked. Yay!

Once I U tubed the the removal and replacement of the gaskets it was super easy. The right gasket change was easy without tools. The left gasket required me to remove the mullion first, which is why I used Utube.

Some have said that the installation took 5 minutes. Mine took less than that, and I did it with one hand. I had a beer in my other hand.

Un-wrapped the basket......Installed with NO tools......

I ordered the needed parts, the correct ones I thought, but when they arrived, I realized they were the wrong parts shipped to me. The reason the wrong parts were shipped to me was because PartsSelect failed to advise me there were none of the parts I needed available so they shipped the left hand basket assembly, door, versus the desired right hand basket assembly, door. I then had to return the wrong parts shipped to me, at my cost of ~$25, and await a refund for the wrong parts originally shipped to me. That's how I did the repair.

Removed the section of refrigerator that dispenses ice and water. Necessary to pry with object that does not scratch like plastic scraper. Then pull out and replace the switch Micro -- only has one Phillips screw holding switch. Replaced the dispenser and snapped on the New button assembly I broke and job was done. Works perfectly now..

Removed the old one and replaced with the new.

Watched a couple of YouTube videos and then went at it

It was more difficult than I expected, I even thought they sent me a wrong part. The glass shelf needs to slide into two cut-outs at the back end of the bin cover. It initially felt like it was impossible. But jut keep pushing gently at a very shallow angle and it will slide right in.

Opened the box. Removed wrapping. Washed the new part. Unloaded old basket. Removed old basket. Set in new basket. Loaded new basket. Closed the door. Even an 80 year old can do it!