LFX25976ST (ASTCNA1) LG Refrigerator - Instructions

This repair is pretty straight forward. Just remove the 3 screws that hold the ice maker and bin assembly in, unplug the wire harness connector, then remove it from the refrigerator door. Once removed you simply need to remove 3 more screws that hold the ice maker to the auger/bin frame, remove the temp sensor, and a couple pieces of tape. Re-assemble the new ice maker in reverse order and you are all set. I think part of the issue I was having was due to mineral buildup in the tray as well so it had a hard time cracking and removing the ice. Not sure why it was overfilling, maybe the sensor was broken or had buildup on it as well. This solved all the problems I was seeing and now it makes great ice that doesn't stick together and form a bridge in the bin.

The spring broke on the flapper (mullion) on my refrigerator. I sent a chat message to PartsSelect (they answered right away) to see if they had a replacement spring but it was not available so had to order the whole mullion. They gave me the part # I would have to order. It arrived quickly. The new mullion didn’t have a visible spring but it worked the same if not better. I just had to remove 2 screws on the center plate on the existing mullion, pull the plate out enough so you will be able to slide the mullion (the wires are under the plate kind of like the ones you see on a ceiling smoke detector) but you can’t get under the plate until you release the mullion. Push up on the mullion so that the plastic tabs on the top and bottom are released. Once the mullion is released (you have to hold it), you’ll see the wires. Unhook the wire part by just pushing down on the little tab and remove it. To install the new one, just reverse the steps. Align the top and bottom plastic tabs to fit into the slots, just enough to hold it in place. If the plastic tabs are not already flipped out, you’ll have to just flip them out. The top tab does not have tension but the bottom tab has tension so just push on it with your finger to flip it out. The plate covering the electrical is a rather tight fit and you have to make sure the little tab on the inside of the plate is above and behind the tab on the inside where the wires are so it slides behind it so you can get it in position before sliding the mullion back down into place and the electrical plate is in place too. Then screw the 2 screws back in. The hardest part is holding the mullion while un-attaching the electrical and just make sure you stuff the wires in enough so you can get the plate back in position. I’m a 75 yr old woman and managed fine by myself. At first when installing the new one, I couldn’t slide the mullion down enough to get the electrical plate in position and then realized I had to have the little tab inside the electrical plate behind the tab inside the wire compartment so they didn’t hit one another when pushing the mullion back down. Then, all went fine.

Remove 2 screws holding to door. Slide assembly up. Unplug connector. Remove old Plate Assembly. Do reverse to reinstall. Plug connector. Push in wires. Slide plate on. Fasten screws. Done

on left side door, I had to remove the flapper (the piece that rotates when you close the door to allow right door to seal. very simple, remove the flapper hingelift up to get the flapper off the door and move it out of the way.
Remove both door gaskets by pulling them out with your hands. Not the orientation of the gaskets because you will have to install the new gaksets in the same orientation.
Press the new gasket in place, into the slot that goes around the inside of the door, by using two fingers to press it into place. Cntinue this all around then go back and press again to assure the gasket is fully seated.
In my case, replacing the gaskets did not solve the issue, but they needed to be replaced do to the condition. The moisture issue was resolve by replacing the flapper (mentioned above)

After noting frost in freezer Right rail started to jam. Noted freezer door was closing crooked. Rail replacement resolved issue. It had been frosting up for some time so Rail must have been broken for a while. Check door seals they were not closing flush.

Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock

Swapped old one with new one. New one had extra plug not needed.

Followed instructions online

Pulled old gasket off by hand. New gasket was easy to install by pushing it into molded cutout in refrigerator door.
Very satisfying to have no glitches in the seamless installation.

Watched the video. Took the screws out, unplugged the connection and slid mullion off. Then plugged the new one in, slid it on and attached the two screws.

Now that you have to buy a complete assembly that includes the drawer in the classy window it's very simple to replace however you buying parts that you don't need simply because G no longer makes the window. Which I find rather odd being as though that they make the whole assembly think and sell windows by themselves for less than 2/3 of what I spent through the whole assembly

Took 2 screws out and disconnect wire and install new part.

Installed new one.

Read the reviews from other members and just did as they said. Needed a screw driver and the info from past persons review couldn’t have been easier.

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.