All Installation Instructions for LG Refrigerator LFX25974SW

rail that holds meat tray broken

remove all trays from refrigerator , remove screw holding rail and install new rail.

Parts Used:

Steve from GEORGE WEST, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Spring in the plate front assembly broke. Door plate assembly would not move into correct position, preventing door from closing.

Followed Youtube video provided on the PartsSelect Website:

https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST

Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.

Parts Used:

Refrigerator Front Plate Assembly

Robert from WARREN, RI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The fridge was not operating and a new main board was recommended

Remove old main board and replace with a new one .

Parts Used:

PCB ASSEMBLY,MAIN

Athan from MIAMI LAKES, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Door Stopper had snapped off

Unscrewed what remained from broken door stop, aligned new one, screwed it in. Done!

Parts Used:

Door Stopper

Lawrence from FALL RIVER, MA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Spring broken in door mullion

Took 2 screws out and disconnect wire and install new part.

Parts Used:

Refrigerator Front Plate Assembly

Wayde from SEMINOLE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Old part did not seal properly

Read the reviews from other members and just did as they said. Needed a screw driver and the info from past persons review couldn’t have been easier.

Parts Used:

Refrigerator Front Plate Assembly

Donald from MERRITT IS, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Ice tray cracked

Removed the old one and replaced with new just remember do your do diligence watch YouTube videos makes repair a lot easier

Parts Used:

Refrigerator Ice Maker Kit Assembly

Eugene from ENCINITAS, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The cover had cracked

1. Remove all food from the shelf and take out the crisper drawers.
2. Remove the glass and take out the crisper frame.
3. Take the screws out of the frame that are holding the cover frame in place and remove the old cover frame..
4. Install the new cover and replace screws.
5. Re- install the drawers and glass.

( I'm a 76 yr old female and did it myself with the help of the instructions you provided!). Thanks

Parts Used:

Crisper Drawer Cover Frame - White

Kathryn from Albuquerque, NM
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Icemaker not working

Removed ice bin
Unscrew the 3 screws.
Lift ice maker for the bottom to remove it but do not pull it until the power is unplug from the part.
Install the new part the same way you removed the old part.
Turn the switch and waiting 48 hours before the ice bin start getting ice

Parts Used:

Ice Maker and Auger Motor Assembly

Franck from ST PETE BEACH, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

cannot get water to the icemaker

i changed the filter and was able to get water to the white coil at the bottom of the dispenser (left door) but could never get water to the icemalker.i also replaced the pump at the bottom of the door as well as the green ebr699172 dispenser electrical board.still can not get water to the icemaker.any help will be greatly appreciated.
paul

Parts Used:

Refrigerator Front Plate Assembly

PAUL from AMARILLO, TX
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker was broken

I just followed the instruction on the part , and everything was very easy.

Parts Used:

Refrigerator Ice Maker Kit Assembly

luis from DIAMOND BAR, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Lower ice maker water feed froze and caused leak. Needed new water valve.

Took pics of original install, removed old valve, water tubes & plugs. Installed new valve, reconnected electronic plugs, water tubes, turned water back on and all has been well since. Thank you for your timely delivery!

Parts Used:

Water Inlet Valve Assembly

Thomas from YORKTOWN, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Ice chute would not open.

Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.

Parts Used: