LFX25974ST (02) LG Refrigerator - Instructions

Pull out old seal with hands. Install new seal into channel by pushing seal into channel with you fingers.

With a small flat blade screw driver, gently pry the corner of the gasket from the door.
Pull it loose across the top, then down the sides.
Wipe the gasket track clean with a damp cloth.
Start installing the new gasket at one of the top corners. Then the other top corner. Press the gasket into the track between the top corners.
Next do the bottom corners. Pressing the bottom between the corners.
Then press in each side.
Elapsed time: 3-5 minutes.

followed detailed movie from Utube video

Unplugged fridge, shut off water supply disconnected water supply from fridge. Remove screws that hold lower cover on back of fridge, removed screws holding valve assembly to fridge. Disconnect two electrical connections, remove black c-clip on out flow water line, lift fitting on outflow line side and pull water line off. Replace with valve assembly in reverse order

Remove 2 screws holding to door. Slide assembly up. Unplug connector. Remove old Plate Assembly. Do reverse to reinstall. Plug connector. Push in wires. Slide plate on. Fasten screws. Done

This was an incredibly easy repair! 1 phillips screwdriver and two screws. Disconnect the small adapter, and you are good to go!

Found the part on Parts Select. Ordered the part, which came quickly. While waiting for delivery. I watched a short video on how to replace this part. I'm a 73 yr. old female, and no trouble at all. I really felt a sense of accomplishment. Thank you Parts Select.

After noting frost in freezer Right rail started to jam. Noted freezer door was closing crooked. Rail replacement resolved issue. It had been frosting up for some time so Rail must have been broken for a while. Check door seals they were not closing flush.

Replaced with new mullion

on left side door, I had to remove the flapper (the piece that rotates when you close the door to allow right door to seal. very simple, remove the flapper hingelift up to get the flapper off the door and move it out of the way.
Remove both door gaskets by pulling them out with your hands. Not the orientation of the gaskets because you will have to install the new gaksets in the same orientation.
Press the new gasket in place, into the slot that goes around the inside of the door, by using two fingers to press it into place. Cntinue this all around then go back and press again to assure the gasket is fully seated.
In my case, replacing the gaskets did not solve the issue, but they needed to be replaced do to the condition. The moisture issue was resolve by replacing the flapper (mentioned above)

The spring broke on the flapper (mullion) on my refrigerator. I sent a chat message to PartsSelect (they answered right away) to see if they had a replacement spring but it was not available so had to order the whole mullion. They gave me the part # I would have to order. It arrived quickly. The new mullion didn’t have a visible spring but it worked the same if not better. I just had to remove 2 screws on the center plate on the existing mullion, pull the plate out enough so you will be able to slide the mullion (the wires are under the plate kind of like the ones you see on a ceiling smoke detector) but you can’t get under the plate until you release the mullion. Push up on the mullion so that the plastic tabs on the top and bottom are released. Once the mullion is released (you have to hold it), you’ll see the wires. Unhook the wire part by just pushing down on the little tab and remove it. To install the new one, just reverse the steps. Align the top and bottom plastic tabs to fit into the slots, just enough to hold it in place. If the plastic tabs are not already flipped out, you’ll have to just flip them out. The top tab does not have tension but the bottom tab has tension so just push on it with your finger to flip it out. The plate covering the electrical is a rather tight fit and you have to make sure the little tab on the inside of the plate is above and behind the tab on the inside where the wires are so it slides behind it so you can get it in position before sliding the mullion back down into place and the electrical plate is in place too. Then screw the 2 screws back in. The hardest part is holding the mullion while un-attaching the electrical and just make sure you stuff the wires in enough so you can get the plate back in position. I’m a 75 yr old woman and managed fine by myself. At first when installing the new one, I couldn’t slide the mullion down enough to get the electrical plate in position and then realized I had to have the little tab inside the electrical plate behind the tab inside the wire compartment so they didn’t hit one another when pushing the mullion back down. Then, all went fine.

Remove 2 screws swing light down a little bit and pull it to front unplug wires . The hard part of job was finding new replacement light, Partselect.com was only sight I could find that had new replacement number and had the light . Other sites including LG site would only tell me the part number on old lights was discontinued 2 of sites said try used appliance dealers

simple economical replacement compared to what LG or local service company wanted to do the same service.

Watched the video. Took the screws out, unplugged the connection and slid mullion off. Then plugged the new one in, slid it on and attached the two screws.

Swapped old one with new one. New one had extra plug not needed.