All Installation Instructions for LG Refrigerator LFX25961SW

Part was delivered broken

The past I ordered was broken upon delivery. I asked for a replacement and was refunded the charge. Tried to contact you but "due to covid" you aren't taking calls. Net result: I ordered the part from another source, got it, installed easily. Won't use you again.

Parts Used:

Door Bin Cover

Karen from GEORGETOWN, TX
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours

1 person found this instruction helpful.

Was this instruction helpful to you?

The switch became intermittent - Possibly a poor designe

Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

Parts Used:

Refrigerator Door Switch

Sidney from ENDICOTT, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Butter bin door had broken

Simple replace of door, fits perfectly

Parts Used:

Door Bin Cover

Mary from DEL MAR, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The plastic cover on the butter area had broken.

Just had to slip the 2 pegs into the existing holes.

Parts Used:

Door Bin Cover

Elizabeth from TALLAHASSEE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Door Stopper had snapped off

Unscrewed what remained from broken door stop, aligned new one, screwed it in. Done!

Parts Used:

Door Stopper

Lawrence from FALL RIVER, MA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

INTERIOR DOOR ACTIVATED LIGHT SWITCH QUIT WORKING

1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!

Parts Used:

Refrigerator Door Switch

JON from OJAI, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

door slight switch failed

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.

Parts Used:

Refrigerator Door Switch

Greg from CASA GRANDE, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Door light switch, 3rd one I have replaced in 6 years made in China.

Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE

Parts Used:

Refrigerator Door Switch

Charles from CURWENSVILLE, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Replace switch

Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape

Parts Used:

Refrigerator Door Switch

Dean from HILLSDALE, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Light quit coming on when door opened.

Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.

Parts Used:

Refrigerator Door Switch

Calvin from Northome, MN
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Lower ice maker water feed froze and caused leak. Needed new water valve.

Took pics of original install, removed old valve, water tubes & plugs. Installed new valve, reconnected electronic plugs, water tubes, turned water back on and all has been well since. Thank you for your timely delivery!

Parts Used:

Water Inlet Valve Assembly

Thomas from YORKTOWN, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

the light did not work when door was opened. At first it would flicker then off completely.

My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)

Parts Used:

Refrigerator Door Switch

Alma from Winterport, ME
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Replace the light switch for the refrigerator

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

Parts Used:

Refrigerator Door Switch

Karyn from DURHAM, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken door gasket retainer

Go to this site on You Tube to watch the "how to" replace the gasket retainer. The retainer I needed did not come with brackets or the cam you will need. You will need transfer them from the old retainer to the new one. Not hard, just be mindful of position of the items you remove to put them back in place the same way. A metal rod holds the brackets and spring in place with a screw on one end to prevent rod from sliding off retainer. The cam has a screw that holds it in place, use from old retainer. If the old cam is not broken use the one from the old retainer. It is not hard and you will save $$$ that you would pay an appliance repair company.

Parts Used: