LFSS2312TP4 Frigidaire Refrigerator - Instructions

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!

I ordered the part from PartSelect using the part number located on the valve itself. The part was delivered in less than 48 hours from the time I entered it. Replacing the valve was easy and went according to the online video instructions provided by PartSelect. The only thing extra was that I had to replace the brass compression fitting on the copper tubing connected to the inlet of the valve. The old one would not seal properly. The compression fitting was about $1.50 at Home Depot. This is my third purchase from PartSelect and I continue to be impressed by them.

Removed new door gasket from box, installed on three side relatively quickly. The last side took some time, the pair of pliers and wiggling to get it to seal to the door frame.

Shut off water supply at the main, drained water from lines, pushed filter in from end of filter then pulled out. Removed the 2 plastic protecting tubes from the inlet and outlet stems. Made sure filter was facing same way as the old one, pushed filter in making sure it was locked, turned water supply on slowly, ran about a gallon of water thru filter. If not done the taste is odd. 5 minute repair.

Simply detached the old ice container by removing four screws and removing one screw holding the lever onto the bottom of the container. A bit of advice; make sure you note how the spring is attached to the lever before removing the screw. It took me a bit to determine how the spring activated the lever when I was reattaching it to the bottom of the container. Also, double check your order before you finalize it. I must have inadvertently hit the item twice so I received two of them. This resulted in me having to return one item and paying for extra shipping both ways. I received the part within two days of my order. It was a very fast turn-around. Also, when I realized that I received two parts and had to call to explain the situation, I found the person on the phone to be extremely helpful and courteous. She sent me information regarding how to return the product and didn't ridicule me once for my stupidity.

Unscrewed old bulb and put in new one

I emptied freezer side of unit, turned unit off, rolled unit away from wall, unplugged unit, turned ice maker water supply off, and took out the ice maker. I then took out old light and replaced it with new light. I then plugged in the unit, turned on the water supply, rolled the unit back in place, placed the ice maker back in the unit and turned the unit back on.
After two hours I placed the frozen items back in the freezer.

great push old in came out and push new one in

Ice was not dispensing. Examined the ice bin and auger, noted that the plastic ring that holds the auger at the front of the bin was broken all the way around. Pulled out old bin, making sure the ice fill level was raised all the way up, and pushed in the new bin. The new bin filled with ice, which promptly turned into a solid mass of ice because the ice maker was also faulty. I replaced that as well and have not had any issues.

Removed the old filter and took off the water caps and pushed it in place. Then I used a pitcher to clear the air from the line and we are good to go for 6 more months

I was really impressed with how easy it was to navigate through your website and found the exact part I needed. I immediately received my glass shelf it took all of 2 seconds.

Put shelf on door, done.

The parts arrived fast, and fit just perfect, they just slide in and snap lock into place. 1 had been broken 2 years ago and I just put off fixing it thinking I would not get the right part, then we broke a seconded one. This web-site made it very easy, and I was pretty sure when I ordered them that they would fit. Thanks for everything

It was real easy took the lines off one by one put them on the new unit one by one same with the three plugs than tighten new unit back on fridge.