LFD25860SW (ASWCLGA) LG Refrigerator - Instructions

I actually glued the item the first time repair was needed - lasted over one year. After it broke again; ordered the part from lg on line; and three days later the part arrived and repair complete. Also, I bought an extra door should the other crisper door fail. These doors and other small white plastic parts are seemingly prone to breakage. I am not rough on my appliances, yet I have had one or two other failues of interior parts. Very happy with lg, nevertheless.

Just searched online, found PartSelect, ordered the part, replaced it. Perfect

Very easy...just remove fruit/vegetable baskets, remove glass shelf and frame, Unscrew the 3 screws that hold in the metal rod from the old one and re-install it in new shelf frame. Voila. I was going to have to wait 2 weeks for a service call and then who knows how long while they ordered the part. Took care of it myself in 3 days - fast, reasonable shipping and part cost. Thank you!

I did it myself and the refrigerator looks like new.

The part labeled as water tank was not pictured on web site, and when it arrived it was a large coil of plastic tubing wire-tied in an oval shape,not a blown p/e tank as original.The oval of tubing would not fit into the door compartment, because of the bulk of the actuating solenoid. No instructions were included. It was necessary to hacksaw the steel solenoid mounting bracket off the solenoid, then contort the solenoid into the compartment to get all parts inside the cover. new connectors had to be purchased, because the the tank/tubing coil was 1/4" od, while the original tank had 5/16"od connections.

I removed the old shelf and disassembled all the parts, removing glass shelf, bins, doors, etc. for use with the new shelf frame. Unfortunately, I hadn't been able to find all the roller assemblies from the original shelf and didn't realize that they were not considered part of the shelf frame. So, after reassembling all the pieces that I had, I still needed to order one additional roller assembly and specialty screw. Knowing this up front would have saved me a nice chunk of time and additional shipping charges. Otherwise, the repair was pretty straightforward.

I got my brother to do the repair....lucky me.

removed control panel, unplugged PCB assembly, removed screws and replaced assembly. reinstalled. super easy and saved me $200 dollars minimum.

I first took off a plastic trip strip which just popped off with a little pull. Then I pulled the gasket off slowly all around the perimeter of the door and snapped off the guide strip with the help of a screwdriver. I installed the gasket next first the guide strip then followed up with the pushing the gasket into the groove all around the door. Did the same procedure on the other door. The gaskets came very well packed and undamaged. It took approximately 2 weeks because one gasket was on back order. Thank you for your help with these parts. It would have cost me 3 times as much if the repairman performed this repair.

At first, ordered only a latch only to discover the mounting strip had instead failed. Ordering parts wasn't difficult although the parts catalog graphic leaves a lot to desire. Once I figured out how to remove the strip (had to remove the seal first and no instructions existed), it was easy to snap out the old and snap in the new part. This sure beat the cost of paying a repairman. However I fear than most homeowners that aren't mechanically inclined wouldnt have been successful because of no instructions and the parts catalog that had poor detail and a very small size.

Removed two drawers and drawer covers, glass shelf and door frame. Replaced in reverse order.

slightly depressed tabs, lined up to mounting holes, released tabs.

I replaced the entire plastic frame to fix the drawers. I'm frustrated that the design requires that I do this. Removed the metal bar that actually provides the support for the front of the frame and the drawers, etc. Three screws to remove and re-install. Easy. After removing the drawers, I just gently bent the drawer cover hinges to slide them out of the frame and tilted the frame out of the fridge. The glass just came out easily as it's not attached with any clips. I had to work to remove the clear plastic panels but a little careful persuasion and I was able to white supports out of the way and remove the panels. Then I removed the aforementioned bar and replaced the glass re-installed the whole assembly.

easy and quickly Thank you for your prompt delivery and excellant service

Simple replacement part.