LFD25860SW (ASWCLGA) LG Refrigerator - Instructions

I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.

Removed screws and the plastic shelf tops from the broken shelf. These parts are sold separately. Do NOT throw anything away until you know you have what you need.
Gentle pull the shelf to spread it enough to get the plastic pieces in. This is the only hard part. Screw the slides onto the new frame. Snap the covers into the crisper fronts. You’ll want to force them in but don’t. They will snap and break.

Watched a couple of YouTube videos and then went at it

Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.

I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.

Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.

Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock

After noting frost in freezer Right rail started to jam. Noted freezer door was closing crooked. Rail replacement resolved issue. It had been frosting up for some time so Rail must have been broken for a while. Check door seals they were not closing flush.

Pops right In

Food off top of shelf, drawers come out, glass tops come off, lift the whole unit up (can be a little heavy. Tilt sideways to angle past doors (remove door's lower bins as needed by removing food and lifting up). Turn upside down, remove 3 screws from metal rod and remove metal rod (may require prying out with screwdriver). Remove textured plastic top pieces from each side; some flexing is required to get one side up, then the other. Remove two hinged drawer covers by pinching in at their hinge points.

This is your last chance to clear all the walls, floor, and ledges at the bottom of your fridge. Just sayin'.

Put new shelf upside down on counter. Transfer metal rod to new shelf, screw it in. Transfer hinged drawer covers. Transfer textured plastic topic pieces, again putting one side (of each) in first and flexing unit a little to get other side in. Turn right side up and angle back into refrigerator.

Bring shelf flat and push to the back of the refrigerator until it is flush with the back. Lower whole unit until it rests on top of the side rails where drawers slide in. Left side has a tongue that will fit into a 2" or so notch near the front, right side will rest on top of a round bumper. Front coldness control should still operate smoothly. Put drawers in to make sure they glide and close smoothly. Put glass shelf on top and press down lightly to make sure lower shelf is stable and glass fits neatly into its plastic frame. Replace any door bins you removed.

Ta da!

Removed old rails and tapped new rails in place. The big problem was finding how to fix the drawer. After searching many online websites, It was my good fortune to find Partselect and a one of their service representatives who
knew how to fix my drawer
and they had the part.

Followed instructions online

Verified that the contact switches were good. Issue was in the main board. Pulled fridge out from wall. Unplugged fridge from wall socket.
Took out 3 screws holding cover of main board. Unplugged main board. Replaced main board and reconnected plugs to main board. Replaced cover with 3 screws. Pushed fridge back against wall.

The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.

Unable to complete repair, had to send parts back
Part should have been PS11732074, but got PS11732704- wrong part
This was a substitute part and was 2" too long

Waiting for refund on this part. It cost me $14.50 to return it by UPS!!!