LFC25760ST (00) LG Refrigerator - Instructions

easy and quickly Thank you for your prompt delivery and excellant service

Simple replacement part.

The online list of parts for this appliance was printed very small and was very intimidatingly busy. Calling the Help Center proved to be our saving grace!! The woman at the Help Center was awesome. Together, we figured what pieces I needed and they arrived within 36 hours; I was extremely impressed. The replacement parts did not include the accessories but we had the needed rollers and metal support bar from the original pieces and installed them readily on the new pieces. All went well and we are happy to have a functioning shelf and vegetable drawers again. I cannot stress enough how content we are and how thrilled I am with the personal service I received on the telephone.

At first, ordered only a latch only to discover the mounting strip had instead failed. Ordering parts wasn't difficult although the parts catalog graphic leaves a lot to desire. Once I figured out how to remove the strip (had to remove the seal first and no instructions existed), it was easy to snap out the old and snap in the new part. This sure beat the cost of paying a repairman. However I fear than most homeowners that aren't mechanically inclined wouldnt have been successful because of no instructions and the parts catalog that had poor detail and a very small size.

Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.

I removed the old shelf and disassembled all the parts, removing glass shelf, bins, doors, etc. for use with the new shelf frame. Unfortunately, I hadn't been able to find all the roller assemblies from the original shelf and didn't realize that they were not considered part of the shelf frame. So, after reassembling all the pieces that I had, I still needed to order one additional roller assembly and specialty screw. Knowing this up front would have saved me a nice chunk of time and additional shipping charges. Otherwise, the repair was pretty straightforward.

No installation instructions. I just took everything out of the shelf holding the drawers and figured it out myself. Unfortunately today's products are made with cheap brittle plastic. This is the second time I have ordered parts for this refrigerator from you and I am glad you are so efficient and shipped orders quickly.

Removed the support bar from the warped frame, which had 3 screws, then reattached the bar to the new frame. The criper drawer front lids was a simple snap in.

removed 1 screw and replaced

The plastic is real weak and the articulation point is not manufactured strong. You have to put one end in a female receiver and flex the tray cover with your fingers crossed hoping it won't snap, while sliding the other side into a similar female receiver on the other side. The Crisper drawer front has not come in yet. Disappointed that you have to buy the entire drawer with a front instead of the front. This is the 2nd one I have replaced. The difference in the Drawer Front...$10.00 and then entire Front and Drawer, $45 plus...

Simply used a flat head screwdriver to get the first few inches of the gasket out of its track and after that just pulled it by hand. New gasket slipped over the door, lined up the corner and pressed into in the track. Checked to see that it was snug all over and we were done. 5 minutes at the very most. Never would have noticed this. Took all the bins out of the freezer to give it a good cleaning and noticed the torn piece hanging. Our refrigerator runs much less often. Expect to see a difference in our electric bill!

snap it on!

Replacement part from PartSelect was OEM, identical to original part. Installation was very quick. Inserted hinge on left side and then depressed the right side to slip it into place. Presto, it was done. Most impressed with PartSelect on the OEM replacement part and very prompt delivery.

Removed white plastic trim and installed new latch / cam shaft

Removal was pretty easy-- replacing crisper drawer took a little care so as not the snap off the hinge- thank you for the speed in which I got my part, no sooner did I order my part- it showed up at my door. your service was outstanding, put you in my favorites just incase I need to order again.