LEDB400FEE0 Frigidaire Dishwasher - Instructions

Putting the new pump in place to test it only took about five minutes. The lower, front, kick-plate panel was already off because I had removed it to figure out what was so loud. The steps after that were:

- Unplugged it and the disposal under the sink (just in case)
- Pulled the wires out of the bottom front of the drain pump
- With a Philips screw driver I loosened the front hose clamp and pulled off the hose
- With the pliers I pinched the back hose clamp and pulled off the hose
- Twisted the pump off of its soft plastic bracket

To put the new one on I reversed the process.

Once it was in place and before I put the panel back on, I plugged in the dishwasher and started a cycle.


The pump was quiet but the person who installed the dishwasher in the first place had the drain hose resting on a spring. When the pump ran it resonated through the spring making a pretty loud noise.

So I unplugged it again, disconnected the hose, fed it under the spring along the floor and then reconnected it. When I plugged it back in and tested it, things were much quieter.

With everything in place I put the panel back on and was finished.

Note: I have worked on dishwashers before and most of the time they have insulation behind the kick-plate panel to quiet them, but this one didn’t. I will probably add that some time later.

Removed bottom plate and heating element brass nuts. Disconnected heating element. Connected new one then replaced brass nuts. Put bottom plate back on. Very easy.

The Spray arm and the support had come off during operation and subsequently melted on the heating element. This was our fault, as a knife had slipped through the lower dish-rack and acted as a ramp to launch the spray arm as it came around. The support was a simple 1/4 turn counter-clockwise until it clicked into place, drop the strainer basket into position around the support, them push the spray arm into place until the catches snap over the retaining ring molded into the support. All told, about 10 minutes, max.

Shut off power to the unit. Removed the screws located along the inside edge of the door, then lifted up slightly on the entire front panel to loosen it from the slotted guides. Be ready to brace the door as there are still some electrical connections that do not need removal to finish the job. Removed two screws that hold the latch assembly in place, leaving the four electrical leads in place (this takes a special screwdriver but I had an attachment with my socket set). Removed the leads one at a time and immediately placed them on the corresponding posts on the new latch (this was to make sure I got the right lead in the right spot). Once all leads were in place, reattached the latch assembly to the inside of the door. The only tricky part was getting the door lined up with the guides and sliding it back into its seated position. That took two people, but only a few tries and it fit. Put the screws back on, turn power back on. Done.

1. Bottom door gasket removed very easy by grabbing left corning and pulling out. Starting with notch on right side, slide the hard plastic side up at a slight angle to catch the slot the gasket will seat in. Slowly moving toward the left, push gasket into seated position. Notch in gasket will make sure it is in correct position. Push gasket all the way in so that it is flush with bottom edge of door. Watch when first sliding gasket in, it has to g at a slight up angle or it will fall into an empty space.
2. Remove Tub gasket by gripping one side and pulling out. Replace in same fashion making sure the angled wedge of gasket is first part that lays flat in slot. Working from one side to the other, make sure the gasket seats completely. Trim excess if necessary.

Disconnected power to the unit at the circuit breaker. Removed the bottom panel of the dishwasher. Used a stubby Phillip screwdriver to remove the single retaining screw holding the high limit thermostat against the bottom of the dishwasher tub. Not only was the thermostat burned out, one of it's electrical connectors was also destroyed. Removed the tape holding the cable bundle together so that I could work on the quick disconnect plug outside of the unit. One end of the quick disconnect plug was completely burned through and needed to be replaced. After doing the necessary electrical repairs and assembling the new thermostat into position I applied power and everything worked fine. It helped having a picture on your website that I could use to identify the correct replacement part.

As another poster had written, on terminal on the thermostat was burned off, most likely due to poor contact by the female spade connector on the end of one of the wires. Removed the DW, tipped it back to gain access, removed the failed thermostat, installed the new one, crimped a new terminal on the end of the wire, and re-installed the DW. Tested all cycles with the heat on and everything worked as designed. Very simple repair, took more time to get the DW out and put it back in than to replace the part and repair the wire.

Remove dishwasher from cabinet flip on it's back. Remove two wire connectors, two torx screws pull pump out and replace very simple. Parts select were great and very fast to ship parts

After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.

Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.

Water leak solved...

Broken friction cable on the right hand side. Remove screws that hold dishwasher to cabinet, pull out the dishwasher far enough to get to the friction cable and rear spring. Remove broken cable. Attach new cable to rear spring and connect to door hinge. Push back dishwasher and screw in the two screws that keep the dishwasher attached to the cabinet. Very simple.

Pulled out old gasket from bottom of door with needle nosed pliers and then put in new one in.

Unscrewed the old spray arm and replace with the new spray arm.

The best part was in the ordering process. Having the diagrams with the parts let me see that I was ordering the correct part. Thanks!

Unscrewed upper sprayer by hand, screwed new one in by hand. Piece of cake!

The spray arm comes off into 3 parts but is really only supposed to be one. I removed the nut from the old assembly and attempted to place the new assembly on by hand. The new nut seemed to be slightly smaller than the original so it would not attach to the dishwasher. Using a kitchen knife, I removed the new nut from the arm unit and attached the new arm to the original nut and it went back on easily. The connection of the new arm to the new nut was 3 tabs that needed to be depressed with the knife and was a different conection method than the assembly that kept coming off in the wash cycle. The replacement part had a much better design than the original.