LDF7932BB ((ABPEEUS)) LG Dishwasher - Instructions

Followed the video provided by your company, done like 1,2,3

The parts are wrong and am trying to return them. There was no return information included with delivery. Calling the Customer Service number for assistance did not work.

I would just like to return these rollers and would like a return address.

Thank you!
Penelope

same as in the video , but the double red wire is on the wrong terminal you have to break the plastic housing on the dishwasher and put it on the first one next to the white wire .if you hook it up the way it is the dishwasher wont work and when you open the door the dishwasher turns on . watch the video real close when it gets to the wire connections you see the double red wire goes over one pin to the one next to the white wire . works fine after that.

Was not able to see where the Stopper, Rollers ( Part # PS3523062) could be attached to the back of the bottom tray, to fix the problem. So the parts were useless.

I ordered four wheels to replace the two that were broken and to have two as spares. The wheels are to be snapped onto the bottom of the lower basket. The new wheels broke upon being installed. My extra wheels came in handy. I put them in very hot water for a few minutes to soften the plastic. I put a little Vaseline on the post they were to be attached to. The wheels then slid on and snapped correctly.

I disconnected the power cord and the drain hose, with a nut driver, under the sink. I removed the bottom plate that covers the water connection under the dishwasher. With the water turned off I used an adjustable wrench to disconnect the water line. I open the door and disconnected the brackets under the counter top, with a phillips screwdriver, that hold the dishwasher in place. I pulled the dish washer out of its enclosure far enough to fully access the spring loaded mechanism to replace the "connector assembly". Then I put it all back where it belonged.. Go slowly and have patience.

Replace basket with new replacement. Ordering and shipment VERY EASY! I have used your service in the past and will continue to in the future. Shipments are fast and accurate.

Remove line to top wash area. Then removed all screws and rubber seal . Then just back step. In about 30 mins. it was ready to run ,

Uninstall dishwasher screws. Lay dishwasher on its side. Remove bottom plate. Remove old drain line. install new line. Test for leak. The trick was figuring out that I could only access the line through the bottom of the dishwasher.

First, PartSelect is great!; fast,& accurate. 1. Inside the dishwasher: remove trays. Remove (A050) lower water sprayer from bottom by pulling up. Remove (F191) top sprayer assembly by pulling away from clip holders. Remove (M110) by removing the holding screws. This part cover the whole sump and has kind-of an open screen circling the unit. Now you will see the white plastic impeller (M120) which is attached the the motor with one Phillips head screw. WARNING. The Phillips head screw (holding the impeller in place) is a REVERSE THREADED SCREW. Turn the screw CLOCKWISE to remove it. Then remove the impeller from the motor shaft. Underneath and outside the washer: Remove the bottom plate. Finally remove the motor by unscrewing the four holding screws and electrical wiring.

These were a simple snap on item. It took longer to carry the parts from the porch that to install. Recently purchased house. Rollers were missing due to overload?? Removed the remaining roller pieces. Cleaned and straightened the axle shafts, spray lubed the tray and snapped the new pieces in place.

parts were not exact match with original, even though ordered from schematic. had to bend the replacement part slightly so it would fit into holder pieces. this took about 10 minutes as I was trying to be careful not to break/cut the coating (which would then lead to rust again). Once the piece was bent, just snapped the rack into place.

The connector assembly connects to a spring to hold the door from falling down. You need to disconnect the power cord, the water line and the drain hose before you move the dishwasher out the kitchen counter. There are several screws that hols the dishwasher in place top, side and bottom. Removed all screws then pull the dishwasher out very slow. Take the side panel by un-screwing all the screws around the panel in my case where five screws (two in the front so you have to open the door to get to them). You need to keep the door down to connect the assembly to the door bracket and the go through the pulley then to the spring, very easy. Put the side panel back and push the dishwasher in place use the same screws and reconnect the hose the water line and the power and you are done.

I disassembled the upper parts of the pump housing and installed the new gasket. It seems to work fine now.

Check the motor and discovered roughness when you turned the shaft. I assume there was a bearing problem. I ordered a new motor from part select and upon the replacement washer is working great! Thanks part select, my part arrived in a timely manner and you guys saved me approx. $500. Thanx again. Richard Sansom