LDF7920ST LG Dishwasher - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door would fall to floor
3 of 3 people
found this instruction helpful.
-
Thomas from ELLIJAY, GA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Very easy just took out two screws that held the dishwasher to counter top.Then pulled dishwasher out just far enough that both door cables are exposed.The hardest part for me was getting the spring stretched enough to clip on.This was a easy installation for most people.
Was this helpful?
Thank you for voting!
Supply line leaked afterwards. Had to replace it. Installers(Home Depot) had it rigged and now it is loose. Going to have to rig it somehow.
3 of 3 people
found this instruction helpful.
-
Mark from IRWIN, PA
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Loosened 3 screws and unhooked supply line and electric box and pulled it out.
Other Parts Used:
Was this helpful?
Thank you for voting!
Our dishwasher door would drop open and land on our feet.
3 of 3 people
found this instruction helpful.
-
Amy from San Marcos, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
My husband was able to slide the dishwasher out, and quickly replace the old connector assembly for the new ones. The old connector assembly had broken at the “rope”. Now the door opens slowly and is as good as new.
Was this helpful?
Thank you for voting!
Two Rollers missing on lower tray.
6 of 13 people
found this instruction helpful.
-
Thomas from BOYNTON BEACH, FL
- Really Easy
- Less than 15 mins
Snapped the rollers on.
Was this helpful?
Thank you for voting!
Dishwasher leaks from door region during washing cycle.
3 of 4 people
found this instruction helpful.
-
tom from grass valley, CA
- Easy
- 30 - 60 mins
-
Pliers
Old door seal appeared ok, no rips and seated evenly all around. Pulled that seal out and replaced with new. Seated new door seal after wetting inserted lip. Tested...leak greatly reduced, but still dripping. Removed seal, placed a rubber rope (same rope used for screening) within the tub recess, then reseated new seal. leak ceased. Also
... Read more
replaced the reservoirs on the left side of the cabinet (guide assembly). Old reservoir had debris within so decided to replace. Used regular pliers for the 3 hose spring clamps underneath, and a pair of large neede nose pliers for the fill flange (regular thread).
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water not coming out of top
3 of 4 people
found this instruction helpful.
-
susan from E WENATCHEE, WA
- Very Difficult
- More than 2 hours
-
Screw drivers
I can’t tell you how it went....ordered my parts on 11/2 and still have not received, they won’t be here For 2 weeks! I won’t get them until 11/15 and 11/16 hmmm 2 weeks for parts......
Other Parts Used:
Was this helpful?
Thank you for voting!
There was a leak in the bottom left corner.
3 of 4 people
found this instruction helpful.
-
Beverly from LOMPOC, CA
- Easy
- 30 - 60 mins
-
Screw drivers
I am 77 years old and got it all on but the corners did not want to go in so I had to call my grandson and he got them in. It still leaked on the bottom left side. It is getting old (11 yrs) so I decided to get a new one. It is actually pretty simple to install, but it does take a little strength.
Was this helpful?
Thank you for voting!
DW door would fall when not latched
2 of 2 people
found this instruction helpful.
-
Robert from DALTON, OH
- Really Easy
- 30 - 60 mins
-
Screw drivers
pulled dishwasher out of cabinet, removed side panel held by screws front and back, removed broken tension rope installed new rope, replaced side panel pushed dishwasher back into cabinet and fastened
to countertop, door works like new now, (the chief cook is happy as she can be)
to countertop, door works like new now, (the chief cook is happy as she can be)
Was this helpful?
Thank you for voting!
Dishwasher would stop during the cycle with nE code
5 of 11 people
found this instruction helpful.
-
Kenneth from BOX SPRINGS, GA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench (Adjustable)
This was my first time repairing a dishwasher. I watched YouTube on how to remove the dishwasher from the cabinet. Afterwards, I removed the bottom of the dishwasher while it was laying flat to get to the motor and micro switch. The only difficulty I had was getting to the motor which required taking the bottom section off of the dishwash
... Read more
er. I could not get an appliance repair company to work on an LG dishwasher. My only option was to repair the dishwasher or bought a new dishwasher. Therefore, my wife and I decided to , make an attempt to repair this one with a backup plan of buying a new one. Luckily, we were able to fix this one within two hours.
This was a $999 dishwasher. We saved the cost of a new dishwasher by taking the time to fix this one.
This was a $999 dishwasher. We saved the cost of a new dishwasher by taking the time to fix this one.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Wrong part
2 of 2 people
found this instruction helpful.
-
Penelope from LAKEVIEW, MI
- Really Easy
- 30 - 60 mins
The parts are wrong and am trying to return them. There was no return information included with delivery. Calling the Customer Service number for assistance did not work.
I would just like to return these rollers and would like a return address.
Thank you!
Penelope
I would just like to return these rollers and would like a return address.
Thank you!
Penelope
Was this helpful?
Thank you for voting!
Front door would fall open without resistance.
2 of 2 people
found this instruction helpful.
-
Ed from COHUTTA, GA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The repair took right at one hour. Repair length of time will depend on what all you have to disconnect to get your dish washer out so you can remove both side panels where you will be able to access the door springs, etc. There is a door spring on each side and I recommend replacing both connectors cords while you have the dishwasher o
... Read more
ut. Mine were both broken. One thing I noticed when doing my repair was that the bracket that is on the bottom of the door was not aligned properly to the small pulley that the connector cords travels under. If yours is out of alignment you will be able to tell once you get the connector cord installed. I used heavy pliers to bend the bracket slightly inward so the connector cords rides in the center of the pulley and not off to the outside as before. This may be why mine broke in the first place. After part replacement, reinstall the door panels and put the washer back in service. There are also YouTube's of this repair so you can see what you are getting into. Basic repair.
Read less
Was this helpful?
Thank you for voting!
Roller Assembly was broken
3 of 5 people
found this instruction helpful.
-
Dale from ITASCA, IL
- Really Easy
- Less than 15 mins
Took off the broken one and snap on the new one.
Was this helpful?
Thank you for voting!
Hinge Cables Broke (Both), AGAIN!!
2 of 2 people
found this instruction helpful.
-
Blair from POTTSTOWN, PA
- Very Easy
- 15 - 30 mins
-
Screw drivers
Cables have broken about every 3-6 months after original ones broke after 8 years. Removed front kick plate screws and remove kick plate, and remove two top screws holding Dishwasher to counter-top. Pull dishwasher out about 10 inches. Remove all broken parts and replace cables. Side dishwasher back in place and reinstall removed screws.
... Read more
I just hope these Cables last longer than the ones I had bought from another source. I have replaced those Cables 5 times already and hope these last MUCH longer. Delivery was very fast from PartSelect.
Read less
Was this helpful?
Thank you for voting!
Two installed roller wheels came off and broke.
2 of 3 people
found this instruction helpful.
-
Charles from WAUWATOSA, WI
- Really Easy
- Less than 15 mins
I ordered four wheels to replace the two that were broken and to have two as spares. The wheels are to be snapped onto the bottom of the lower basket. The new wheels broke upon being installed. My extra wheels came in handy. I put them in very hot water for a few minutes to soften the plastic. I put a little Vaseline on the post they were
... Read more
to be attached to. The wheels then slid on and snapped correctly.
Read less
Was this helpful?
Thank you for voting!
No power to dishwasher. Confirmed that outlet had power coming out.
4 of 9 people
found this instruction helpful.
-
JOHN from FORT MYERS, FL
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upsi
... Read more
de down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day.
Read less
Was this helpful?
Thank you for voting!