Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The light would not turn on (had the problem for years!) and the seal around the door was not very good.
2 of 2 peoplefound this instruction helpful.
Penelope from WEST CHESTER, OH
Really Easy
15 - 30 mins
Pliers, Screw drivers
1. Pull out the old gasket & push in the new one!
2. Pop out the light assembly with a screwdriver, disconnect the wire bracket, (the hardest part so I used pliers to grip the plastic) and connect the new one...pay attention to the direction to put it back in the space and you’re done! IF I CAN DO IT, YOU CAN DO IT! (Also check
... Read more you tube videos for accurate instructions & correct terminology!!!)
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Was this helpful?
Thank you for voting!
Not making ice but could hear the solenoid trying to work
1 personfound this instruction helpful.
Jesse from Pella, IA
Very Easy
15 - 30 mins
Screw drivers, Wrench (Adjustable)
I turned off the water supply. Took off the access panel at the bottom of the fridge. Disconnected the waterlines from the valve. Remove the screw hole in the valve in place install the waterlines on the new valve attach the new valve to the refrigerator, reinstalled the back panel turn on the water And it made ice.
Was this helpful?
Thank you for voting!
INTERIOR DOOR ACTIVATED LIGHT SWITCH QUIT WORKING
1 personfound this instruction helpful.
JON from OJAI, CA
Really Easy
15 - 30 mins
Screw drivers
1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs o
... Read moren the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!
Read less
Was this helpful?
Thank you for voting!
bad switch
1 personfound this instruction helpful.
Michael from TONAWANDA, NY
Easy
15 - 30 mins
Screw drivers
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this helpful?
Thank you for voting!
Lights didn't come on when door was opened
1 personfound this instruction helpful.
Philip from Ashland, MA
A Bit Difficult
15 - 30 mins
Pliers, Screw drivers
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this helpful?
Thank you for voting!
No problem
1 personfound this instruction helpful.
Mable from SILVER SPRING, MD
Very Easy
Less than 15 mins
Screw drivers
As much as I am a hands on person, I did not do the installation myself. A friend who was visiting offer to do for me, and I simply did not refuse the offer. In my perception it really seems quite easy, a job that that I could do myself with ease.
Was this helpful?
Thank you for voting!
Door light switch, 3rd one I have replaced in 6 years made in China.
1 personfound this instruction helpful.
Charles from CURWENSVILLE, PA
Really Easy
Less than 15 mins
Pliers, Screw drivers
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this helpful?
Thank you for voting!
Replace switch
1 personfound this instruction helpful.
Dean from HILLSDALE, MI
Really Easy
Less than 15 mins
Screw drivers
Read previous tips Taped off area around switch to protect surface Used putty knife to extract switch Used screwdriver to separate connector from switch Plugged in connector Pushed switch assembly into opening Removed tape
Was this helpful?
Thank you for voting!
The switch became intermittent - Possibly a poor designe
1 personfound this instruction helpful.
Sidney from ENDICOTT, NY
Very Easy
Less than 15 mins
Screw drivers
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
Was this helpful?
Thank you for voting!
my cover lamp broke
1 personfound this instruction helpful.
Marissa from BOYNTON BEACH, FL
Very Easy
Less than 15 mins
I just popped in the new cover lamp. It took less than 5 mins. if that much.
Was this helpful?
Thank you for voting!
door slight switch failed
1 personfound this instruction helpful.
Greg from CASA GRANDE, AZ
Really Easy
Less than 15 mins
Pliers
Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.
Was this helpful?
Thank you for voting!
The right hand glide for the top freezer drawer was broken.
1 personfound this instruction helpful.
Cathrine from NEW ORLEANS, LA
Very Easy
15 - 30 mins
Replaced the glide.
Was this helpful?
Thank you for voting!
the light did not work when door was opened. At first it would flicker then off completely.
1 of 2 peoplefound this instruction helpful.
Alma from Winterport, ME
Very Easy
Less than 15 mins
Screw drivers
My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)
My Orders
