LCE756BS8 Frigidaire Dryer - Instructions

I removed the top of the washer by removing two screws on the back. I located and bypassed the lid switch to make sure that wasn't the problem. The problem still existed so I removed the two screws that hold the front panel of the washer. Using a flashlight, I located the drive belt and immediately saw that it was out of position and had pieces missing. I cut and removed the old belt, placed the new belt on the tub pulley and slowly maneuvered it onto the motor drive wheel. I then squeezed the tensioner pulley so that the belt was seated. I turned the timer dial which started the washer and it immediately began pumping the water out of the tub. Problem solved!

I removed the broken knob from the metal shaft with a pair of pliers and slid the new knob in place.

Piece of cake!

I removed the front panel to see the belt was snapped in two. The front roller is sping loaded, so I gave it a little tention, slid the belt back on and viola! it was that easy. If your washer starts to vibrate more and sounds louder than normal, get a belt as soon as possible because that may be the problem. Once I put on the new belt, the machine ran as quiet as it did when I first bought it.

I don't think it would take others as long as it took me.
I had to take the drum out to get to the limiter. And my dryer is in a builtin housing with limited space in front of the dryer - so lots of manuevers to get access.

The limiter was very easy to find, thanks to diagrams on this site. The space between drum and limiter made it impossible to get to the limiter screws without removing drum. Found very helpful drum removal instructions on PartSelect here:

http://www.partselect.com/PS1148434-Frigidaire-134503600-Dryer-Drum-Belt.htm?SourceCode=13&ModelNum=FSE748GFS0

Great site - thank you.

I used a screwdriver to remove the front of the washing machine, fit the belt around the main pulley, held in the spring loaded tension pulley, and threaded the belt aound. It works great! I really need this inexpensive repair, since my job was downsized, and I can't afford to pay anyone.

Used nut driver to remove screw and cover from dryer cord terminal block, used screw driver to remove two screws securing old terminal block, cut dammaged wire and stripped wire back and crimped on new terminal connecter, replaced old terminal block with new one, replaced two screws, installed new cord, and replaced cover plate and screw.

followed video and replaced part( cleaned and vacuumed dryer while I had it apart),relatively easy repair

I removed the front access panel above the washer and removed the top dryer front panel. Then pulled out the drum and noticed the drum support ball stud had broken off, rather than order a new one, I welded it back on with a mig welder. I then replaced the drum support bearing and reinstalled the drum. I then installed the new belt before placing the front top panel in place. I removed the small vented panel on the back side to access the belt tensioner and fit the belt around the pulley and motor shaft. The whole job took less than an hour.

Removed old filter, installed new filter

Removed the front, door and all. Replaced both upper and lower seals and allowed glue to dry for 24 hours. Removed 3 screws attaching drum to pivot in rear. While drum was out, relubricated pivot seat and ball. Installed new drum which has been re-designed, has strip around entire lip now. Seals are different, so both have to be replaced with ones in kit, supplied tube of glue is not enough to do the job, so used gator glue. Had trouble installing the 3 screws that attach it to the pivot. Finally re-assembled entire front panel and replaced the door. Started the dryer and it worked as new.

Basically, i followed instructions on 1 video i seen, but was able to shorten repair by not removing drum, and was still able to access the thermal limiter switch to remove old one and install new one. Worked like a charm. Thanks Dan

Not having the repair manual made the repair more difficult. Prior experience made the job somewhat easy. Had to study every move to make sure no parts were not broken but overall the repair went without any problems. I found out that the bearing plate was removable to facilitate removal and replacement of the heating element. Advise if you are doing a repair of an appliance you don't know much about, take your time and everything should go well for you.

I took off the front panel of the washer and placed the belt on the large tub wheel and then the smaller wheel. I placed the belt over the adjustable third wheel and turned the tub in order to get the belt all the way in the grooves. Thirty minutes max to replace. Thanks, my order was 100% satisfactory

removed top and front panel on stackable dyer unit. 3 screws at back of the inside of the drum, and the drum was out. installed new bearing and belt and all was good.

The hardest part was getting to the part and removing it and putting it back on. The schematics that you had on your website helped us locate where it needed to go and, hopefully, that will solve our problem.